Falsche Verbrauchswerte beim Laden

[Rico]

Hallo zusammen,
seit zwei Jahren nutze ich openWB. Die ganze Zeit relativ zuverlässig und ich bin sehr zufrieden. Seit kurzem hauen die Werte während des PV-Ladens jedoch nicht mehr hin.

Kurz zum Setup:

SolarEdge-Wechselrichter für PV
Go-e Wallbox
Victron Wechselrichter für den Speicher
Victron EVU

Problem:
Wenn nicht geladen wird, sehe ich die korrekten Werte:
PV um die 2,2kW
Netz-Exp. um die 2,0kW
Hausverbrauch um die 300W
Speicher-Ladung um die 11W

Wenn openWB nun das PV-Laden beginnt, fällt der Hausverbrauch auf 0W und der Netz-Imp. wird mir zweistellig angezeigt. Und das, obwohl die Wallbox mit ca. 1,6kW mehr lädt, als die PV liefert und der Speicher nur mit 110W unterstützt.

Geändert habe ich in letzter Zeit nichts an der Konfiguration. Ich habe lediglich die SD-Karte gespiegelt.

Habt ihr Idee, woran das Problem liegt und wie ich es in den Griff bekomme?

Im Anhang ein paar Screenshots zur Verdeutlichung. Hier fiel mir übrigens auch gerade auf, dass im Bereich Speicher-Ladung und -Entladung seltsamerweise ein negatives Vorzeichen steht und der Wert seltsamen formatiert ist. Das war sonst auch nicht so...

Danke und viele Grüße
Ricardo

[Rico]

Und hier noch die log:

2025-08-10 18:18:16: PID: 12629: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:18:16: PID: 12629: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:18:16: PID: 12629: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:18:15: PID: 12629: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: EVU 1:V/-3A 2: V/-2A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 51 uberschuss -51 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: pv1watt -1791 pv2watt pvwatt -1791 ladeleistung 3240 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:18:15: PID: 12629: speicherleistung -124 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:18:12: PID: 12629: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:18:07: PID: 11349: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:18:06: PID: 11349: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:18:06: PID: 11349: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:18:06: PID: 11349: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:18:05: PID: 11349: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:18:05: PID: 11349: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:18:05: PID: 11349: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:18:05: PID: 11349: EVU 1:V/-3A 2: V/-2A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:18:05: PID: 11349: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:18:04: PID: 11349: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -74 uberschuss 74 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:18:04: PID: 11349: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:18:04: PID: 11349: pv1watt -769 pv2watt pvwatt -769 ladeleistung 3240 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:18:04: PID: 11349: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:18:04: PID: 11349: speicherleistung -181 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:18:02: PID: 11349: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:57: PID: 10025: pv ladung auf 15A reduziert (LV1) at 349 nurpvlademodus nurpv.sh 2025-08-10 18:17:57: PID: 10025: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:55: PID: 10025: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:55: PID: 10025: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:55: PID: 10025: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:54: PID: 10025: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: EVU 1:V/-3A 2: V/-3A 3: V/9A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 12 uberschuss -12 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: lla1 15 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: pv1watt -1931 pv2watt pvwatt -1931 ladeleistung 3440 llalt 16 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:54: PID: 10025: speicherleistung -192 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:51: PID: 10025: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:47: PID: 8743: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:45: PID: 8743: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:45: PID: 8743: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:45: PID: 8743: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:44: PID: 8743: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: EVU 1:V/-3A 2: V/-3A 3: V/9A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 4 uberschuss -4 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: lla1 15 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: pv1watt -1942 pv2watt pvwatt -1942 ladeleistung 3440 llalt 16 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:44: PID: 8743: speicherleistung -150 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:41: PID: 8743: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:37: PID: 7466: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:35: PID: 7466: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:35: PID: 7466: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:35: PID: 7466: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:34: PID: 7466: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: EVU 1:V/-3A 2: V/-3A 3: V/9A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 34 uberschuss -34 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: lla1 15 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: pv1watt -1932 pv2watt pvwatt -1932 ladeleistung 3460 llalt 16 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:34: PID: 7466: speicherleistung -150 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:31: PID: 7466: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:27: PID: 6188: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:25: PID: 6188: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:25: PID: 6188: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:25: PID: 6188: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:24: PID: 6188: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: EVU 1:V/-3A 2: V/-3A 3: V/9A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 22 uberschuss -22 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: lla1 15 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: pv1watt -1933 pv2watt pvwatt -1933 ladeleistung 3460 llalt 16 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:24: PID: 6188: speicherleistung -151 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:21: PID: 6188: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:17: PID: 4881: pv ladung auf 16A erhoeht (LV1) at 305 nurpvlademodus nurpv.sh 2025-08-10 18:17:17: PID: 4881: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:15: PID: 4881: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:15: PID: 4881: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:15: PID: 4881: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:14: PID: 4881: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -135 uberschuss 135 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: pv1watt -1939 pv2watt pvwatt -1939 ladeleistung 3240 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:14: PID: 4881: speicherleistung -52 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:11: PID: 4881: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:07: PID: 3596: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:05: PID: 3596: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:17:05: PID: 3596: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:17:05: PID: 3596: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:17:04: PID: 3596: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -12 uberschuss 12 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: pv1watt -1945 pv2watt pvwatt -1945 ladeleistung 3250 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:17:04: PID: 3596: speicherleistung -62 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:17:01: PID: 3596: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:57: PID: 2285: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:55: PID: 2285: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:55: PID: 2285: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:55: PID: 2285: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:54: PID: 2285: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -17 uberschuss 17 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: pv1watt -1950 pv2watt pvwatt -1950 ladeleistung 3250 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:54: PID: 2285: speicherleistung -52 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:51: PID: 2285: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:47: PID: 951: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:45: PID: 951: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:45: PID: 951: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:45: PID: 951: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:44: PID: 951: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 9 uberschuss -9 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: pv1watt -1956 pv2watt pvwatt -1956 ladeleistung 3240 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:44: PID: 951: speicherleistung -47 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:41: PID: 951: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:37: PID: 32068: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:35: PID: 32068: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:35: PID: 32068: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:35: PID: 32068: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:34: PID: 32068: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -1 uberschuss 1 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: pv1watt -1957 pv2watt pvwatt -1957 ladeleistung 3230 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:34: PID: 32068: speicherleistung -36 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:31: PID: 32068: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:26: PID: 30790: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:25: PID: 30790: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:25: PID: 30790: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:25: PID: 30790: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:24: PID: 30790: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 36 uberschuss -36 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: pv1watt -1961 pv2watt pvwatt -1961 ladeleistung 3220 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:24: PID: 30790: speicherleistung -26 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:21: PID: 30790: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:16: PID: 29513: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:15: PID: 29513: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:15: PID: 29513: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:15: PID: 29513: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:14: PID: 29513: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: EVU 1:V/-3A 2: V/-3A 3: V/8A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug 22 uberschuss -22 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: lla1 14 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: pv1watt -1969 pv2watt pvwatt -1969 ladeleistung 3250 llalt 15 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:14: PID: 29513: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:11: PID: 29513: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:07: PID: 28204: pv ladung auf 15A erhoeht (LV1) at 305 nurpvlademodus nurpv.sh 2025-08-10 18:16:07: PID: 28204: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:05: PID: 28204: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:16:05: PID: 28204: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:16:05: PID: 28204: Zeit zum abfragen aller Werte 3 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:16:04: PID: 28204: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: EVU 1:V/-3A 2: V/-3A 3: V/7A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -114 uberschuss 114 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: lla1 13 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: pv1watt -1974 pv2watt pvwatt -1974 ladeleistung 3000 llalt 14 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:16:04: PID: 28204: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:16:01: PID: 28204: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:59: PID: 26880: pv ladung auf 14A erhoeht (LV1) at 305 nurpvlademodus nurpv.sh 2025-08-10 18:15:58: PID: 26880: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:57: PID: 26880: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:57: PID: 26880: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:57: PID: 26880: Zeit zum abfragen aller Werte 5 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:55: PID: 26880: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: EVU 1:V/-3A 2: V/-3A 3: V/7A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 0 wattbezug -245 uberschuss 245 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: lla1 12 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: pv1watt -1976 pv2watt pvwatt -1976 ladeleistung 2770 llalt 13 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:55: PID: 26880: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:52: PID: 26880: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:48: PID: 25579: pv ladung auf 13A erhoeht (LV1) at 305 nurpvlademodus nurpv.sh 2025-08-10 18:15:47: PID: 25579: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:46: PID: 25579: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:46: PID: 25579: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:46: PID: 25579: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:45: PID: 25579: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:45: PID: 25579: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:45: PID: 25579: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:45: PID: 25579: EVU 1:V/-3A 2: V/-3A 3: V/5A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:45: PID: 25579: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:44: PID: 25579: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 348 wattbezug -488 uberschuss 488 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:44: PID: 25579: lla1 10 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:44: PID: 25579: pv1watt -1981 pv2watt pvwatt -1981 ladeleistung 2300 llalt 11 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:44: PID: 25579: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:44: PID: 25579: speicherleistung -26 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:42: PID: 25579: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:38: PID: 24238: pv ladung auf 11A erhoeht (LV1) at 305 nurpvlademodus nurpv.sh 2025-08-10 18:15:37: PID: 24238: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:36: PID: 24238: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:36: PID: 24238: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:36: PID: 24238: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:35: PID: 24238: chargestatlp1 1 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:35: PID: 24238: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: EVU 1:V/-3A 2: V/-3A 3: V/2A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 348 wattbezug -1060 uberschuss 1060 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: lla1 5 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: pv1watt -1990 pv2watt pvwatt -1990 ladeleistung 1190 llalt 6 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:34: PID: 24238: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:32: PID: 24238: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:28: PID: 22944: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:26: PID: 22944: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:26: PID: 22944: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:26: PID: 22944: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:25: PID: 22944: chargestatlp1 0 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: EVU 1:V/-3A 2: V/-3A 3: V/-1A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 348 wattbezug -1674 uberschuss 1674 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: lla1 0 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: pv1watt -1996 pv2watt pvwatt -1996 ladeleistung 0 llalt 6 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:25: PID: 22944: speicherleistung -26 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:22: PID: 22944: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:17: PID: 21645: nur pv ladung auf 6 starten (LV1) at 115 nurpvlademodus nurpv.sh 2025-08-10 18:15:17: PID: 21645: Überschuss 1658; mindestens 1400 (LV1) at 104 nurpvlademodus nurpv.sh 2025-08-10 18:15:17: PID: 21645: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:16: PID: 21645: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:16: PID: 21645: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:16: PID: 21645: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:15: PID: 21645: chargestatlp1 0 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:15: PID: 21645: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: EVU 1:V/-3A 2: V/-3A 3: V/-2A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 360 wattbezug -1658 uberschuss 1658 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: lla1 0 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: pv1watt -1998 pv2watt pvwatt -1998 ladeleistung 0 llalt 0 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:14: PID: 21645: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:12: PID: 21645: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:08: PID: 20111: PV Einschaltverzögerung auf 30 erhöht, Ziel 30 (LV1) at 112 nurpvlademodus nurpv.sh 2025-08-10 18:15:08: PID: 20111: Überschuss 1658; mindestens 1400 (LV1) at 104 nurpvlademodus nurpv.sh 2025-08-10 18:15:08: PID: 20111: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:06: PID: 20111: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:15:06: PID: 20111: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:15:06: PID: 20111: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:15:05: PID: 20111: chargestatlp1 0 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: EVU 1:V/-3A 2: V/-3A 3: V/-2A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20113: ##### cron5min.sh finished ##### (LV0) at 313 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:05: PID: 20111: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 369 wattbezug -1658 uberschuss 1658 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: lla1 0 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: pv1watt -2001 pv2watt pvwatt -2001 ladeleistung 0 llalt 0 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:15:05: PID: 20111: speicherleistung -26 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:15:04: PID: 20113: logfile cleanup triggered (LV1) at 310 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:04: PID: 20456: push buttons disabled (LV1) at 41 pushButtonsSetup /var/www/html/openWB/runs/pushButtons/pushButtonsHelper.sh 2025-08-10 18:15:04: PID: 20456: rse disabled (LV1) at 41 rseSetup /var/www/html/openWB/runs/rse/rseHelper.sh Failed to stop dnsmasq.service: Unit dnsmasq.service not loaded. Failed to stop hostapd.service: Unit hostapd.service not loaded. 2025-08-10 18:15:03: PID: 20456: checking network setup (LV1) at 103 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: external openWB, daemon mode or socket mode not configured (LV1) at 97 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: legacy run server is already running (LV1) at 60 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: Starting legacy run server... (LV1) at 54 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: smart home handler is already running (LV1) at 42 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: smart home handler... (LV1) at 39 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: mqtt handler is already running (LV1) at 33 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: Starting MQTT handler... (LV1) at 31 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: Modul tibbergetprices.py: Modullaufzeit 0.004781 s 2025-08-10 18:15:03: Modul tibbergetprices.py: Ausreichend zukuenftige Preise in bisheriger Preisliste 2025-08-10 18:15:03: PID: 20456: modbus tcp server already running (LV1) at 25 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: Modul tibbergetprices.py: Bereinige bisherige Preisliste 2025-08-10 18:15:03: Modul tibbergetprices.py: Lese bisherige Preisliste 2025-08-10 18:15:03: PID: 20456: Starting modbus server... (LV1) at 23 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20456: Starting OpenWB services (LV0) at 21 start /var/www/html/openWB/runs/services.sh 2025-08-10 18:15:03: PID: 20113: current ip: 192.168.178.113 (LV1) at 293 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20113: updating daily yield stats (LV1) at 164 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20113: electricity provider configured; trigger price update (LV1) at 157 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20113: Netzschutz konfiguriert; aktuelle Frequenz: 0 (LV1) at 109 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20113: daily csv updated: /var/www/html/openWB/web/logging/data/daily/20250810.csv (LV1) at 101 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20113: ##### cron5min.sh started ##### (LV0) at 23 main /var/www/html/openWB/runs/cron5min.sh 2025-08-10 18:15:02: PID: 20111: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:14:57: PID: 18825: PV Einschaltverzögerung auf 20 erhöht, Ziel 30 (LV1) at 112 nurpvlademodus nurpv.sh 2025-08-10 18:14:57: PID: 18825: Überschuss 1684; mindestens 1400 (LV1) at 104 nurpvlademodus nurpv.sh 2025-08-10 18:14:57: PID: 18825: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:14:56: PID: 18825: Timing Umschaltung: 480 / 480 (LV1) at 17 u1p3pswitch u1p3p.sh 2025-08-10 18:14:56: PID: 18825: automatische Umschaltung aktiv (LV1) at 16 u1p3pswitch u1p3p.sh 2025-08-10 18:14:56: PID: 18825: Zeit zum abfragen aller Werte 4 Sekunden (LV1) at 186 main /var/www/html/openWB/regel.sh 2025-08-10 18:14:55: PID: 18825: chargestatlp1 0 chargestatlp2 0 chargestatlp3 0 (LV1) at 1274 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: plugstatlp1 1 plugstatlp2 0 plugstatlp3 0 (LV1) at 1273 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: lp1enabled 1 lp2enabled 1 lp3enabled 1 (LV1) at 1272 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: EVU 1:V/-3A 2: V/-3A 3: V/-2A (LV1) at 1271 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: lla3 0 llv3 0 llas13 llas23 soclp1 0 soclp2 (LV1) at 1270 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: lla2 0 llv2 0 llas12 llas22 sofortll 32 hausverbrauch 331 wattbezug -1684 uberschuss 1684 (LV1) at 1269 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: lla1 0 llv1 0 llas11 llas21 mindestuberschuss 1400 abschaltuberschuss 0 lademodus 2 (LV1) at 1268 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: pv1watt -1995 pv2watt pvwatt -1995 ladeleistung 0 llalt 0 nachtladen 0 nachtladen 0 minimalA 6 maximalA 32 (LV1) at 1267 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: etproviderprice etprovidermaxprice (LV1) at 1265 loadvars loadvars.sh 2025-08-10 18:14:54: PID: 18825: speicherleistung -20 speichersoc 99 (LV1) at 1262 loadvars loadvars.sh 2025-08-10 18:14:52: PID: 18825: **** Regulation loop start **** (LV1) at 77 main /var/www/html/openWB/regel.sh 2025-08-10 18:14:49: PID: 17519: PV Einschaltverzögerung auf 10 erhöht, Ziel 30 (LV1) at 112 nurpvlademodus nurpv.sh 2025-08-10 18:14:49: PID: 17519: Überschuss 1679; mindestens 1400 (LV1) at 104 nurpvlademodus nurpv.sh 2025-08-10 18:14:49: PID: 17519: anzahlphasen 1 (LV1) at 585 main /var/www/html/openWB/regel.sh 2025-08-10 18:14:47: PID: 17519: auf 1 Phasen geaendert (LV1) at 99 u1p3pswitch u1p3p.sh Umschaltung auf 1 Phase erfolgreich: fsp=1 Phaseneinstellung fsp vorher: 0 go-e serial number: geschwärzt Go-e mit IP 192.168.178.119 Umschaltung auf 1 Phasen 2025-08-10 18:14:46: PID: 17519: Nur PV Laden derzeit 3 Phasen, auf 1 konfiguriert, aendere... (LV1) at 93 u1p3pswitch u1p3p.sh 2025-08-10 18:14:46

[Rico]

Ich habe das Problem gefunden:

Mein Victron EVU hat falsche Werte geliefert, weil eine Strommesschelle geöffnet war.

OpenWB konnte nichts dafür, läuft weiterhin super und ich bin nach wie vor sehr zufrieden und sehr dankbar.

Der thread kann gerne gelöscht werden. Sorry für die Umstände!