Gerade hat mein Auto angefangen zu laden obwohl nicht mehr genügend Sonne da ist. Das SoC-Modul ist schuld. Irgendwas hat Tesla wohl wieder geändert, auf jeden Fall konnte der SoC nicht ermittelt werden und wird als Null angezeigt. Null ist kleiner als der eingestellte Mindest-SoC also fängt das Laden an.
Wir hatten hier ja schon mal die Diskussion, ob das Verhalten beim Zielladen bei nicht erfolgreichem SoC-auslesen nicht doch besser stattfinden sollte. Da war ich der Meinung, ja auf jeden Fall, denn besser das Auto ist zu voll als zu leer. (Die openWB hat nicht geladen, das fragliche Auto war am Morgen zu leer)
Beim Mindest-SoC wird nun also geladen obwohl das Erreichen des Ziel-SoCs nicht feststellbar ist und somit das Auto komplett voll geladen wird.
Nun denke ich, dass man doch einen Fehlerwert-SoC definieren müsste, auf den die jeweilige Laderlogiken - vielleich sogar einstellbar - reagieren. Beim Zielladen würde ich laden wollen, beim Mindest-SoC eher nicht. Aber es gibt ja auch ein SoC-Ladeziel bei Sofortladen, im PV-laden und im Zeitladen.
Vielleicht könnte der Punkt auf irgendeine ToDo-Liste, das ist ja wegen der vielen Stellen nun ein größerer Brocken, wenn man das implementiert. Und wenn man es einstellbar macht, braucht‘s das auch noch.
Rückmeldungen 2.1.5 Release & Release Patch 1/2
-
Gero
- Beiträge: 3417
- Registriert: Sa Feb 20, 2021 9:55 am
- Has thanked: 4 times
- Been thanked: 59 times
Re: Rückmeldungen 2.1.5 Release
Nun ist wieder morgens und ich kann das, was gestern nicht ins Auto ging, nachladen. Aber die openWB regelt den Ladestrom zu hoch!
PV sind 8,9kW, Ladesleistung sind 10,2kW. Sollte es daran liegen, dass ich gerade meinen Heizstab in den Hausverbrauch habe rechnen lassen?
Oha, Heizstab ausgeschaltet: (eigentlich hätte der ausgehen müssen, "Ausschaltschwelle anpassen" ist gesetzt)
https://paste.openwb.de/5BzyrH2amAh6gvj
edit: Nachgestellt bekomme ich es leider nicht nochmal, mittlerweile kommt zu viel vom Dach als dass der Speicher entladen werden müsste. Der wird nun einfach nur nicht mehr geladen - achso: Lademodus prio Fahrzeug.
- lade.jpg (53.62 KiB) 1234 mal betrachtet
Oha, Heizstab ausgeschaltet: (eigentlich hätte der ausgehen müssen, "Ausschaltschwelle anpassen" ist gesetzt)
- lade2.jpg (61.21 KiB) 1234 mal betrachtet
https://paste.openwb.de/5BzyrH2amAh6gvj
edit: Nachgestellt bekomme ich es leider nicht nochmal, mittlerweile kommt zu viel vom Dach als dass der Speicher entladen werden müsste. Der wird nun einfach nur nicht mehr geladen - achso: Lademodus prio Fahrzeug.
openWB-series2, openWB-Buchse, E3/DC S10pro+19.5kWh, 30kWp Ost-Süd, Model 3 und Ion
Re: Rückmeldungen 2.1.5 Release
Ist im Release angepasst, dass er nicht automatisch nach dem Update angezeigt wird.BJ Axel hat geschrieben: ↑Di Aug 27, 2024 12:37 pm Merci!
Kurzen Herzinfarktmoment: Nach Update & Neustart kam der "Einrichtungsassistent". WEITER, dann ABBRUCH.
Zum Glück waren alle Settings übernommen worden.
Colors-Theme auf dem Display sieht auch sehr schön aus, leider sind die beiden Ladepunkte im Verlauf farblich nicht unterschieden.
Re: Rückmeldungen 2.1.5 Release
Doch der Regelbereich wird berücksichtigt. Dein Bezug liegt doch auch innerhalb des Regelbereichs.andlem hat geschrieben: ↑Di Aug 27, 2024 2:47 pm Regelgrenzen beim PV-Laden werden nicht berücksichtigt
Um den Fehler offensichtlich zu machen, habe ich diese auf Individuell -500 W und +500 W eingestellt. Die openWB setzt alle 10 s einen neuen Stromwert, obwohl die Regelgrenzen nicht überschritten werden. Ich erwarte, dass der Stromwert nicht nachgeregelt wird, bis die Regelgrenzen überschritten werden. Hier der Auszug aus dem Log über zwei Regelperioden:
Code: Alles auswählen
2024-08-27 15:38:30,236 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 15:38:30,333 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten ['Hichi'] 2024-08-27 15:38:30,345 - {modules.common.component_context:25} - {DEBUG:device2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:30,361 - {urllib3.connectionpool:227} - {DEBUG:device0} - Starting new HTTP connection (1): 192.168.188.23:80 2024-08-27 15:38:30,379 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:30,388 - {modules.common.component_context:25} - {DEBUG:set values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:30,414 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /measurements.xml HTTP/1.1" 200 None 2024-08-27 15:38:30,430 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: <?xml version='1.0' encoding='UTF-8'?><root><Device Name='PIKO 3.6 MP' Type='Inverter' Serial='755810BL006202240015' BusAddress='1' NetBiosName='INV006202240015' IpAddress='192.168.188.27' DateTime='2024-08-27T15:37:24'><Measurements><Measurement Value='238.872' Unit='V' Type='AC_Voltage'/><Measurement Value='11.443' Unit='A' Type='AC_Current'/><Measurement Value='2729.150' Unit='W' Type='AC_Power'/><Measurement Value='49.991' Unit='Hz' Type='AC_Frequency'/><Measurement Value='418.171' Unit='V' Type='DC_Voltage'/><Measurement Value='6.532' Unit='A' Type='DC_Current'/><Measurement Value='2737.890' Unit='W' Type='DC_Power'/><Measurement Value='40.000' Unit='°C' Type='Temp'/><Measurement Value='nan' Unit='W' Type='Consumption PV'/><Measurement Value='nan' Unit='W' Type='Consumption Grid'/><Measurement Value='nan' Unit='W' Type='GridPower'/><Measurement Value='100.0' Unit='%' Type='Dearting'/></Measurements></Device></root> 2024-08-27 15:38:30,439 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:30,456 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /gen.yield.total.chart.js HTTP/1.1" 200 None 2024-08-27 15:38:30,465 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: var chartData = { "labels": [ "2000","2001","2002","2003","2004","2005","2006","2007","2008","2009","2010","2011","2012","2013","2014","2015","2016","2017","2018","2019","2020","2021","2022","2023","2024"], "datasets": [ { "strokeColor": style_strokecolor.color, "fillColor": style_fillcolor.color, "data": [ 0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000, 0.000000,0.000000,2.326921,4.263654,4.414874,4.505618,4.035070,4.734527,4.436030,3.309975] } ] } var max = 5; var steps = 5; document.getElementById("labelValueId").innerHTML = " 32.031MWh"; var myBar = new Chart(document.getElementById("canvasId") .getContext("2d")) .Bar(chartData, { "pointDot": false, "datasetFill": false, "scaleOverride": true, "scaleLabel": "<%=value%> MWh", "scaleSteps": steps, "scaleStartValue": 0, "scaleStepWidth": Math.ceil(max / steps), "scaleLineColor": style_linecolor.color, "scaleFontColor": style_fontcolor.color }); 2024-08-27 15:38:30,478 - {modules.common.store._api:26} - {DEBUG:device2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:30,557 - {urllib3.connectionpool:452} - {DEBUG:device0} - http://192.168.188.23:80 "GET /cm?cmnd=status%2010 HTTP/1.1" 200 None 2024-08-27 15:38:30,560 - {modules.common.req:32} - {DEBUG:device0} - Get-Response: {"StatusSNS":{"Time":"2024-08-27T14:38:31","SM":{"WhImported":16262696.339180,"WhExported":21749651.650630,"W":92.310,"W1":-147.690,"W2":157.690,"W3":82.310}}} 2024-08-27 15:38:32,867 - {modules.common.store._api:26} - {DEBUG:device0} - Raw data CounterState(currents=[-0.6421304347826087, 0.6856086956521739, 0.3578695652173913], powers=[-147.69, 157.69, 82.31], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.33918, exported=21749651.65063, power=92.31, frequency=50) 2024-08-27 15:38:32,893 - {modules.common.component_context:25} - {DEBUG:component2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:32,895 - {modules.common.store._api:26} - {DEBUG:component2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:32,896 - {modules.common.component_context:25} - {DEBUG:update values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:32,897 - {modules.common.store._api:31} - {INFO:component2} - Saving InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:32,981 - {modules.common.component_context:25} - {DEBUG:component0} - Update Komponente ['Hichi'] 2024-08-27 15:38:32,982 - {modules.common.store._api:31} - {INFO:component0} - Saving CounterState(currents=[-0.6421304347826087, 0.6856086956521739, 0.3578695652173913], powers=[-147.69, 157.69, 82.31], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.33918, exported=21749651.65063, power=92.31, frequency=50) 2024-08-27 15:38:33,040 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:33,235 - {modules.ripple_control_receivers.dimm_kit.ripple_control_receiver:27} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: State.CLOSED, RSE-Kontakt 2: State.CLOSED 2024-08-27 15:38:33,236 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 15:38:33,240 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:33,242 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 15:38:33,330 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 0: [51.21, 39.29, 39.68]A 2024-08-27 15:38:33,331 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 0: 29397.9W 2024-08-27 15:38:33,332 - {control.ev:909} - {DEBUG:MainThread} - RFID 0011214001 wird EV 2 zugeordnet. 2024-08-27 15:38:33,334 - {control.chargepoint.chargepoint:557} - {DEBUG:MainThread} - EV-Phasenzahl beschränkt die nutzbaren Phasen auf 1 2024-08-27 15:38:33,338 - {control.chargepoint.chargepoint:682} - {INFO:MainThread} - LP 3, EV: BMW 225xe (EV-Nr.2): Theoretisch benötigter Strom 6A, Lademodus pv_charging, Submodus: Chargemode.PV_CHARGING, Phasen: 1, Priorität: False, max. Ist-Strom: 10.57 2024-08-27 15:38:33,343 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724765903.7499952, power=281.4800000000003, imported=2741411.7901248764, exported=0) 2024-08-27 15:38:33,345 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00266488, power1: 281.48, power2: 331.25 2024-08-27 15:38:33,346 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 0.816425 2024-08-27 15:38:33,348 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 0.816425 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724765913.343548, power=331.25000000000006, imported=2741412.6065495466, exported=0) 2024-08-27 15:38:33,350 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=False), get=Get(soc=0, daily_exported=0.0, daily_imported=0.0, fault_str='Kein Fehler.', fault_state=0, imported=0, exported=0, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 15:38:33,353 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=4048.0, daily_exported=0.0, power=2490.21, imported=2713904.05, exported=0)) 2024-08-27 15:38:33,355 - {control.data:266} - {INFO:MainThread} - cp3 ChargepointData(control_parameter=ControlParameter(chargemode=<Chargemode.PV_CHARGING: 'pv_charging'>, current_plan=None, failed_phase_switches=1, imported_at_plan_start=None, imported_instant_charging=None, limit=', da die maximale Leistung an Zähler {} erreicht ist.', phases=1, prio=False, required_current=6, required_currents=[6, 0.0, 0.0], state=4, submode=<Chargemode.PV_CHARGING: 'pv_charging'>, timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=True, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=68), currents=[10.57, -0.02, 0.04], daily_imported=4048.0, daily_exported=0.0, evse_current=1170, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=2713904.05, phases_in_use=1, plug_state=True, power=2490.21, rfid_timestamp=None, rfid=None, serial_number='21299772', soc=None, soc_timestamp=None, state_str=None, vehicle_id=None, voltages=[236.46, 237.2, 238.73]), set=Set(charging_ev=2, charging_ev_prev=2, current=11.7, energy_to_charge=0, loadmanagement_available=True, log=Log(chargemode_log_entry='pv_charging', costs=0, imported_at_mode_switch=2713754.88, imported_at_plugtime=2709708.98, imported_since_mode_switch=143.07000000029802, imported_since_plugged=4188.970000000205, range_charged=0.7153500000014902, time_charged='0:03', timestamp_start_charging=1724765683.492532, ev=2, prio=False, rfid='0011214001', serial_number=None, soc_at_start=65, soc_at_end=None, range_at_start=15.0, range_at_end=None), manual_lock=False, phases_to_use=1, plug_state_prev=True, plug_time=1724688005.191368, required_power=1380.0, rfid='0011214001', target_current=0, charging_ev_data=<control.ev.Ev object at 0x7046ca00>), config=Config(configuration={'mode': 'series', 'ip_address': 'localhost', 'duo_num': 0}, ev=0, name='Interne openWB', type='internal_openwb', template=0, connected_phases=3, phase_1=1, auto_phase_switch_hw=True, control_pilot_interruption_hw=True, id=3)) 2024-08-27 15:38:33,358 - {control.data:266} - {INFO:MainThread} - cpt0 CpTemplateData(autolock=Autolock(active=False, plans={}, wait_for_charging_end=False), id=0, max_current_multi_phases=16, max_current_single_phase=16, name='Standard Ladepunkt-Vorlage', disable_after_unplug=False, valid_tags=['0003411712', '0006721162', '0007501485', '0011214001']) 2024-08-27 15:38:33,359 - {control.data:266} - {INFO:MainThread} - counter0 CounterData(config=Config(max_currents=[40, 40, 40], max_total_power=27000), get=Get(powers=[-147.69, 157.69, 82.31], currents=[-0.64, 0.69, 0.36], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], frequency=50, daily_exported=8194.0, daily_imported=1572.0, imported=16262696.33918, exported=21749651.65063, fault_state=0, fault_str='Kein Fehler.', power=92.31), set=Set(error_counter=0, reserved_surplus=0, released_surplus=0, raw_power_left=29397.9, raw_currents_left=[51.21, 39.29, 39.68], surplus_power_left=0)) 2024-08-27 15:38:33,362 - {control.data:241} - {INFO:MainThread} - counter_all_data CounterAllData(config=Config(home_consumption_source_id=None, reserve_for_not_charging=False), get=Get(hierarchy=[{'id': 0, 'type': 'counter', 'children': [{'id': 2, 'type': 'inverter', 'children': []}, {'id': 3, 'type': 'cp', 'children': []}]}]), set=Set(loadmanagement_active=False, home_consumption=331.25000000000006, smarthome_power_excluded_from_home_consumption=0, invalid_home_consumption=0, daily_yield_home_consumption=5810.0, imported_home_consumption=2741412.6065495466, disengageable_smarthome_power=0)) 2024-08-27 15:38:33,364 - {control.data:266} - {INFO:MainThread} - ct0 ChargeTemplateData(name='Standard-Ladeprofil-Vorlage', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='stop', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:33,367 - {control.data:266} - {INFO:MainThread} - ct1 ChargeTemplateData(name='Corsa', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=6, min_current=0, feed_in_limit=False, min_soc=0, max_soc=70), scheduled_charging=ScheduledCharging(plans={'3': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2024-08-10', weekly=[False, False, False, False, False, False, False]), current=9, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=90, soc_scheduled=90), time='13:00')}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=100)))) 2024-08-27 15:38:33,369 - {control.data:266} - {INFO:MainThread} - ct2 ChargeTemplateData(name='BMW 225xe', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={'2': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2023-11-11', weekly=[False, False, False, False, False, False, False]), current=14, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=100, soc_scheduled=100), time='11:50')}), instant_charging=InstantCharging(current=17, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:33,370 - {control.data:266} - {INFO:MainThread} - ev0 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=True, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,370 - {control.data:266} - {INFO:MainThread} - ev1 EvData(set=Set(soc_error_counter=0), charge_template=1, ev_template=1, name='Corsa', tag_id=['0003411712', '0007501485'], get=Get(soc=72, soc_timestamp=1724765717.317447, force_soc_update=False, range=272, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,372 - {control.data:266} - {INFO:MainThread} - ev2 EvData(set=Set(soc_error_counter=0), charge_template=2, ev_template=2, name='BMW 225xe', tag_id=['0006721162', '0011214001'], get=Get(soc=68, soc_timestamp=1724765685.227685, force_soc_update=False, range=18.0, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,374 - {control.data:266} - {INFO:MainThread} - ev3 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='neues Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,375 - {control.data:266} - {INFO:MainThread} - et0 EvTemplateData(name='Standard-Fahrzeug-Vorlage', max_current_multi_phases=16, max_phases=3, phase_switch_pause=2, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=False, control_pilot_interruption_duration=4, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=82000, efficiency=90, nominal_difference=1, keep_charge_active_duration=40) 2024-08-27 15:38:33,383 - {control.data:266} - {INFO:MainThread} - et1 EvTemplateData(name='Corsa', max_current_multi_phases=16, max_phases=3, phase_switch_pause=120, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=46000, efficiency=92, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:33,386 - {control.data:266} - {INFO:MainThread} - et2 EvTemplateData(name='BMW 225xe', max_current_multi_phases=16, max_phases=1, phase_switch_pause=50, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=20000, min_current=6, max_current_single_phase=16, battery_capacity=6000, efficiency=100, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:33,388 - {control.data:245} - {INFO:MainThread} - general_data GeneralData(chargemode_config=ChargemodeConfig(instant_charging=InstantCharging(phases_to_use=3), phase_switch_delay=5, pv_charging=PvCharging(bat_power_reserve=0, bat_power_reserve_active=False, control_range=[-500, 500], feed_in_yield=15000, phase_switch_delay=7, phases_to_use=1, bat_power_discharge=0, bat_power_discharge_active=False, min_bat_soc=50, bat_mode='ev_mode', switch_off_delay=60, switch_off_threshold=300, switch_on_delay=6, switch_on_threshold=1400), retry_failed_phase_switches=True, scheduled_charging=ScheduledCharging(phases_to_use=0, phases_to_use_pv=0), time_charging=TimeCharging(phases_to_use=3), unbalanced_load_limit=20, unbalanced_load=True), control_interval=10, extern_display_mode='local', extern=False, external_buttons_hw=False, grid_protection_active=False, grid_protection_configured=True, grid_protection_random_stop=0, grid_protection_timestamp=None, http_api=False, mqtt_bridge=False, prices=Prices(bat=0.0003, cp=0, grid=0.0003, pv=0.00012), range_unit='km', ripple_control_receiver=RippleControlReceiver(get=RippleControlReceiverGet(fault_state=0, fault_str='Kein Fehler.', override_value=100), module={'name': 'openWB Dimm- & Control-Kit', 'type': 'dimm_kit', 'configuration': {'ip_address': '192.168.0.158', 'port': 8899, 'modbus_id': 1}}, override_reference=<OverrideReference.CHARGEPOINT: 'chargepoint'>)) 2024-08-27 15:38:33,392 - {control.data:246} - {INFO:MainThread} - general_data-display local 2024-08-27 15:38:33,392 - {control.data:247} - {INFO:MainThread} - graph_data GraphData(config=Config(duration=120)) 2024-08-27 15:38:33,393 - {control.data:248} - {INFO:MainThread} - optional_data OptionalData(et=Et(get=EtGet(fault_state=0, fault_str='Kein Fehler.', prices={})), int_display=InternalDisplay(active=False, on_if_plugged_in=True, pin_active=False, pin_code='0000', standby=60, theme=<modules.display_themes.cards.config.CardsDisplayTheme object at 0x70484580>), led=Led(active=False), rfid=Rfid(active=True)) 2024-08-27 15:38:33,394 - {control.data:266} - {INFO:MainThread} - pv2 PvData(config=Config(max_ac_out=0), get=Get(currents=[0.0, 0.0, 0.0], daily_exported=16285.0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026669.0, fault_state=0, fault_str='Kein Fehler.', power=-2729.15)) 2024-08-27 15:38:33,394 - {control.data:250} - {INFO:MainThread} - pv_all_data PvAllData(config=Config(configured=True), get=Get(daily_exported=16285.0, fault_str='Kein Fehler.', fault_state=0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026669.0, power=-2729.15)) 2024-08-27 15:38:33,395 - {control.data:266} - {INFO:MainThread} - system {'update_in_progress': False, 'perform_update': False, 'backup_cloud': {'backup_before_update': True}, 'ip_address': '192.168.188.43', 'current_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_branch': 'Release', 'current_branch_commit': '2024-08-27 12:33:48 +0200 [a069e0f37]', 'current_missing_commits': ['2024-08-27 12:33:48 +0200 [a069e0f37] - Merge pull request #1843 from openWB/master', '2024-06-04 08:52:24 +0200 [417a30647] - Merge pull request #1649 from openWB/master', '2024-03-19 06:56:08 +0100 [a6b648645] - Merge pull request #1490 from openWB/master', '2024-03-14 11:48:27 +0100 [1d1d842c5] - Merge pull request #1367 from openWB/master'], 'boot_done': True, 'datastore_version': 54, 'dataprotection_acknowledged': True, 'usage_terms_acknowledged': True, 'debug_level': 10, 'release_train': 'master', 'version': '2.1.5', 'lastlivevaluesJson': {'timestamp': 1724765903, 'time': '15:38:23', 'grid': -0.177, 'house-power': 0.281, 'charging-all': 2.27, 'pv-all': 2.729, 'cp3-power': 2.27, 'ev1-soc': 72, 'ev2-soc': 68}, 'installAssistantDone': True, 'module_update_completed': True} 2024-08-27 15:38:33,397 - {control.data:279} - {INFO:MainThread} - device0 {'name': 'Hichi', 'type': 'json', 'id': 0, 'configuration': {'url': 'http://192.168.188.23/cm?cmnd=status%2010'}} 2024-08-27 15:38:33,402 - {control.data:281} - {INFO:MainThread} - component0 {'name': 'Hichi', 'type': 'counter', 'id': 0, 'configuration': {'jq_power': '.StatusSNS.SM.W', 'jq_exported': '.StatusSNS.SM.WhExported', 'jq_imported': '.StatusSNS.SM.WhImported', 'jq_powers': ['.StatusSNS.SM.W1', '.StatusSNS.SM.W2', '.StatusSNS.SM.W3'], 'jq_currents': [None, None, None]}} 2024-08-27 15:38:33,404 - {control.data:279} - {INFO:MainThread} - device2 {'name': 'Kostal Piko', 'type': 'kostal_steca', 'id': 2, 'configuration': {'ip_address': '192.168.188.27'}} 2024-08-27 15:38:33,406 - {control.data:281} - {INFO:MainThread} - component2 {'name': 'Kostal Piko', 'type': 'inverter', 'id': 2, 'configuration': {'variant_steca': False}} 2024-08-27 15:38:33,407 - {control.data:253} - {INFO:MainThread} - 2024-08-27 15:38:33,407 - {control.algorithm.algorithm:25} - {INFO:MainThread} - # Algorithmus 2024-08-27 15:38:33,408 - {control.counter:390} - {DEBUG:MainThread} - LP3 Switch-Off-Threshold prüfen: 92.31W, Schwelle: 300W, freigegebener Ãœberschuss 0W, Einspeisegrenze 0W 2024-08-27 15:38:33,411 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:33,413 - {control.algorithm.algorithm:30} - {INFO:MainThread} - **Mindestrom setzen** 2024-08-27 15:38:33,415 - {control.algorithm.min_current:20} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:33,416 - {control.counter:179} - {DEBUG:MainThread} - Zähler 0: [45.21, 39.29, 39.68]A verbleibende Ströme, 28017.9W verbleibende Leistung 2024-08-27 15:38:33,418 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 6A 2024-08-27 15:38:33,419 - {control.algorithm.algorithm:32} - {INFO:MainThread} - **Sollstrom setzen** 2024-08-27 15:38:33,422 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:33,424 - {control.counter:501} - {DEBUG:MainThread} - Zähler 0: Begrenzung der verbleibenden Leistung auf 1017.9000000000015W 2024-08-27 15:38:33,428 - {control.algorithm.algorithm:38} - {INFO:MainThread} - **PV-geführten Strom setzen** 2024-08-27 15:38:33,431 - {control.algorithm.filter_chargepoints:102} - {DEBUG:MainThread} - Geordnete Ladepunkte [3] 2024-08-27 15:38:33,432 - {control.algorithm.surplus_controlled:45} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:33,435 - {control.loadmanagement:76} - {DEBUG:MainThread} - Leistungsüberschreitung auf 1017.9000000000015W korrigieren: [10.0, 0.0, 0.0] 2024-08-27 15:38:33,435 - {control.algorithm.surplus_controlled:121} - {DEBUG:MainThread} - Ungenutzten Sollstrom aufschlagen ergibt 11.55565217391305A. 2024-08-27 15:38:33,436 - {control.counter:186} - {DEBUG:MainThread} - Zähler 0: [39.65434782608695, 39.29, 39.68]A verbleibende Ströme, -259.89999999999986W verbleibender Ãœberschuss 2024-08-27 15:38:33,436 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 11.55565217391305A 2024-08-27 15:38:33,437 - {control.process:23} - {INFO:MainThread} - # Ladung starten. 2024-08-27 15:38:33,438 - {control.process:109} - {INFO:MainThread} - LP3: set current 11.56 A, state CHARGING_ALLOWED 2024-08-27 15:38:33,440 - {modules.common.component_context:25} - {DEBUG:set current cp3} - Update Komponente ['Ladepunkt'] kill: (420): Kein passender Prozess gefunden seems like atreboot.sh finished normally 2024-08-27 15:38:33,729 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/power, Payload 2490.21, vorherige Payload: 2270.37 2024-08-27 15:38:33,731 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/imported, Payload 2713904.05, vorherige Payload: 2713897.95 2024-08-27 15:38:33,733 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/home_consumption, Payload 331.25000000000006, vorherige Payload: 281.4800000000003 2024-08-27 15:38:33,737 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/imported_home_consumption, Payload 2741412.6065495466, vorherige Payload: 2741411.7901248764 2024-08-27 15:38:34,601 - {helpermodules.command:126} - {DEBUG:Commands} - Befehl: {'command': 'getDailyLog', 'data': {'day': '20240827'}}, Connection-ID: rjmkd 2024-08-27 15:38:35,751 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:40,770 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:40,772 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=handler10Sec, args=(), kwargs={}) 2024-08-27 15:38:40,773 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 15:38:40,808 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten ['Hichi'] 2024-08-27 15:38:40,811 - {modules.common.component_context:25} - {DEBUG:device2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:40,815 - {urllib3.connectionpool:227} - {DEBUG:device0} - Starting new HTTP connection (1): 192.168.188.23:80 2024-08-27 15:38:40,821 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:40,825 - {modules.common.component_context:25} - {DEBUG:set values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:40,833 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /measurements.xml HTTP/1.1" 200 None 2024-08-27 15:38:40,836 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: <?xml version='1.0' encoding='UTF-8'?><root><Device Name='PIKO 3.6 MP' Type='Inverter' Serial='755810BL006202240015' BusAddress='1' NetBiosName='INV006202240015' IpAddress='192.168.188.27' DateTime='2024-08-27T15:37:34'><Measurements><Measurement Value='238.853' Unit='V' Type='AC_Voltage'/><Measurement Value='11.506' Unit='A' Type='AC_Current'/><Measurement Value='2737.200' Unit='W' Type='AC_Power'/><Measurement Value='49.993' Unit='Hz' Type='AC_Frequency'/><Measurement Value='418.430' Unit='V' Type='DC_Voltage'/><Measurement Value='6.547' Unit='A' Type='DC_Current'/><Measurement Value='2744.030' Unit='W' Type='DC_Power'/><Measurement Value='39.900' Unit='°C' Type='Temp'/><Measurement Value='nan' Unit='W' Type='Consumption PV'/><Measurement Value='nan' Unit='W' Type='Consumption Grid'/><Measurement Value='nan' Unit='W' Type='GridPower'/><Measurement Value='100.0' Unit='%' Type='Dearting'/></Measurements></Device></root> 2024-08-27 15:38:40,842 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:40,851 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /gen.yield.total.chart.js HTTP/1.1" 200 None 2024-08-27 15:38:40,855 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: var chartData = { "labels": [ "2000","2001","2002","2003","2004","2005","2006","2007","2008","2009","2010","2011","2012","2013","2014","2015","2016","2017","2018","2019","2020","2021","2022","2023","2024"], "datasets": [ { "strokeColor": style_strokecolor.color, "fillColor": style_fillcolor.color, "data": [ 0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000, 0.000000,0.000000,2.326921,4.263654,4.414874,4.505618,4.035070,4.734527,4.436030,3.309983] } ] } var max = 5; var steps = 5; document.getElementById("labelValueId").innerHTML = " 32.031MWh"; var myBar = new Chart(document.getElementById("canvasId") .getContext("2d")) .Bar(chartData, { "pointDot": false, "datasetFill": false, "scaleOverride": true, "scaleLabel": "<%=value%> MWh", "scaleSteps": steps, "scaleStartValue": 0, "scaleStepWidth": Math.ceil(max / steps), "scaleLineColor": style_linecolor.color, "scaleFontColor": style_fontcolor.color }); 2024-08-27 15:38:40,856 - {modules.common.store._api:26} - {DEBUG:device2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:40,906 - {urllib3.connectionpool:452} - {DEBUG:device0} - http://192.168.188.23:80 "GET /cm?cmnd=status%2010 HTTP/1.1" 200 None 2024-08-27 15:38:40,908 - {modules.common.req:32} - {DEBUG:device0} - Get-Response: {"StatusSNS":{"Time":"2024-08-27T14:38:41","SM":{"WhImported":16262696.482510,"WhExported":21749651.650630,"W":55.930,"W1":-184.220,"W2":158.010,"W3":82.140}}} 2024-08-27 15:38:43,231 - {modules.common.store._api:26} - {DEBUG:device0} - Raw data CounterState(currents=[-0.8009565217391305, 0.6869999999999999, 0.3571304347826087], powers=[-184.22, 158.01, 82.14], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.48251, exported=21749651.65063, power=55.93, frequency=50) 2024-08-27 15:38:43,237 - {modules.common.component_context:25} - {DEBUG:component2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:43,239 - {modules.common.component_context:25} - {DEBUG:update values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:43,243 - {modules.common.store._api:26} - {DEBUG:component2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:43,246 - {modules.common.store._api:31} - {INFO:component2} - Saving InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:43,269 - {modules.common.component_context:25} - {DEBUG:component0} - Update Komponente ['Hichi'] 2024-08-27 15:38:43,271 - {modules.common.store._api:31} - {INFO:component0} - Saving CounterState(currents=[-0.8009565217391305, 0.6869999999999999, 0.3571304347826087], powers=[-184.22, 158.01, 82.14], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.48251, exported=21749651.65063, power=55.93, frequency=50) 2024-08-27 15:38:43,320 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:43,523 - {modules.ripple_control_receivers.dimm_kit.ripple_control_receiver:27} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: State.CLOSED, RSE-Kontakt 2: State.CLOSED 2024-08-27 15:38:43,524 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 15:38:43,526 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:43,527 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 15:38:43,613 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 0: [51.370000000000005, 39.29, 39.68]A 2024-08-27 15:38:43,614 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 0: 29444.14W 2024-08-27 15:38:43,615 - {control.ev:909} - {DEBUG:MainThread} - RFID 0011214001 wird EV 2 zugeordnet. 2024-08-27 15:38:43,617 - {control.chargepoint.chargepoint:557} - {DEBUG:MainThread} - EV-Phasenzahl beschränkt die nutzbaren Phasen auf 1 2024-08-27 15:38:43,620 - {control.chargepoint.chargepoint:682} - {INFO:MainThread} - LP 3, EV: BMW 225xe (EV-Nr.2): Theoretisch benötigter Strom 6A, Lademodus pv_charging, Submodus: Chargemode.PV_CHARGING, Phasen: 1, Priorität: False, max. Ist-Strom: 10.57 2024-08-27 15:38:43,625 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724765913.343548, power=331.25000000000006, imported=2741412.6065495466, exported=0) 2024-08-27 15:38:43,626 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00285602, power1: 331.25, power2: 293.06 2024-08-27 15:38:43,628 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 0.891521 2024-08-27 15:38:43,629 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 0.891521 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724765923.6252253, power=293.05999999999966, imported=2741413.4980709245, exported=0) 2024-08-27 15:38:43,630 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=False), get=Get(soc=0, daily_exported=0.0, daily_imported=0.0, fault_str='Kein Fehler.', fault_state=0, imported=0, exported=0, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 15:38:43,632 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=4048.0, daily_exported=0.0, power=2500.07, imported=2713912.11, exported=0)) 2024-08-27 15:38:43,634 - {control.data:266} - {INFO:MainThread} - cp3 ChargepointData(control_parameter=ControlParameter(chargemode=<Chargemode.PV_CHARGING: 'pv_charging'>, current_plan=None, failed_phase_switches=1, imported_at_plan_start=None, imported_instant_charging=None, limit=', da die maximale Leistung an Zähler {} erreicht ist.', phases=1, prio=False, required_current=6, required_currents=[6, 0.0, 0.0], state=4, submode=<Chargemode.PV_CHARGING: 'pv_charging'>, timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=True, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=68), currents=[10.57, -0.02, 0.04], daily_imported=4048.0, daily_exported=0.0, evse_current=1156, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=2713912.11, phases_in_use=1, plug_state=True, power=2500.07, rfid_timestamp=None, rfid=None, serial_number='21299772', soc=None, soc_timestamp=None, state_str=None, vehicle_id=None, voltages=[236.57, 237.81, 238.48]), set=Set(charging_ev=2, charging_ev_prev=2, current=11.56, energy_to_charge=0, loadmanagement_available=True, log=Log(chargemode_log_entry='pv_charging', costs=0, imported_at_mode_switch=2713754.88, imported_at_plugtime=2709708.98, imported_since_mode_switch=149.1699999999255, imported_since_plugged=4195.069999999832, range_charged=0.7458499999996274, time_charged='0:03', timestamp_start_charging=1724765683.492532, ev=2, prio=False, rfid='0011214001', serial_number=None, soc_at_start=65, soc_at_end=None, range_at_start=15.0, range_at_end=None), manual_lock=False, phases_to_use=1, plug_state_prev=True, plug_time=1724688005.191368, required_power=1380.0, rfid='0011214001', target_current=0, charging_ev_data=<control.ev.Ev object at 0x70484f40>), config=Config(configuration={'mode': 'series', 'ip_address': 'localhost', 'duo_num': 0}, ev=0, name='Interne openWB', type='internal_openwb', template=0, connected_phases=3, phase_1=1, auto_phase_switch_hw=True, control_pilot_interruption_hw=True, id=3)) 2024-08-27 15:38:43,635 - {control.data:266} - {INFO:MainThread} - cpt0 CpTemplateData(autolock=Autolock(active=False, plans={}, wait_for_charging_end=False), id=0, max_current_multi_phases=16, max_current_single_phase=16, name='Standard Ladepunkt-Vorlage', disable_after_unplug=False, valid_tags=['0003411712', '0006721162', '0007501485', '0011214001']) 2024-08-27 15:38:43,636 - {control.data:266} - {INFO:MainThread} - counter0 CounterData(config=Config(max_currents=[40, 40, 40], max_total_power=27000), get=Get(powers=[-184.22, 158.01, 82.14], currents=[-0.8, 0.69, 0.36], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], frequency=50, daily_exported=8194.0, daily_imported=1572.0, imported=16262696.48251, exported=21749651.65063, fault_state=0, fault_str='Kein Fehler.', power=55.93), set=Set(error_counter=0, reserved_surplus=0, released_surplus=0, raw_power_left=29444.14, raw_currents_left=[51.370000000000005, 39.29, 39.68], surplus_power_left=0)) 2024-08-27 15:38:43,637 - {control.data:241} - {INFO:MainThread} - counter_all_data CounterAllData(config=Config(home_consumption_source_id=None, reserve_for_not_charging=False), get=Get(hierarchy=[{'id': 0, 'type': 'counter', 'children': [{'id': 2, 'type': 'inverter', 'children': []}, {'id': 3, 'type': 'cp', 'children': []}]}]), set=Set(loadmanagement_active=False, home_consumption=293.05999999999966, smarthome_power_excluded_from_home_consumption=0, invalid_home_consumption=0, daily_yield_home_consumption=5810.0, imported_home_consumption=2741413.4980709245, disengageable_smarthome_power=0)) 2024-08-27 15:38:43,638 - {control.data:266} - {INFO:MainThread} - ct0 ChargeTemplateData(name='Standard-Ladeprofil-Vorlage', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='stop', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:43,640 - {control.data:266} - {INFO:MainThread} - ct1 ChargeTemplateData(name='Corsa', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=6, min_current=0, feed_in_limit=False, min_soc=0, max_soc=70), scheduled_charging=ScheduledCharging(plans={'3': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2024-08-10', weekly=[False, False, False, False, False, False, False]), current=9, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=90, soc_scheduled=90), time='13:00')}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=100)))) 2024-08-27 15:38:43,641 - {control.data:266} - {INFO:MainThread} - ct2 ChargeTemplateData(name='BMW 225xe', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={'2': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2023-11-11', weekly=[False, False, False, False, False, False, False]), current=14, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=100, soc_scheduled=100), time='11:50')}), instant_charging=InstantCharging(current=17, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:43,643 - {control.data:266} - {INFO:MainThread} - ev0 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=True, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,644 - {control.data:266} - {INFO:MainThread} - ev1 EvData(set=Set(soc_error_counter=0), charge_template=1, ev_template=1, name='Corsa', tag_id=['0003411712', '0007501485'], get=Get(soc=72, soc_timestamp=1724765717.317447, force_soc_update=False, range=272, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,645 - {control.data:266} - {INFO:MainThread} - ev2 EvData(set=Set(soc_error_counter=0), charge_template=2, ev_template=2, name='BMW 225xe', tag_id=['0006721162', '0011214001'], get=Get(soc=68, soc_timestamp=1724765685.227685, force_soc_update=False, range=18.0, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,646 - {control.data:266} - {INFO:MainThread} - ev3 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='neues Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,647 - {control.data:266} - {INFO:MainThread} - et0 EvTemplateData(name='Standard-Fahrzeug-Vorlage', max_current_multi_phases=16, max_phases=3, phase_switch_pause=2, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=False, control_pilot_interruption_duration=4, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=82000, efficiency=90, nominal_difference=1, keep_charge_active_duration=40) 2024-08-27 15:38:43,648 - {control.data:266} - {INFO:MainThread} - et1 EvTemplateData(name='Corsa', max_current_multi_phases=16, max_phases=3, phase_switch_pause=120, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=46000, efficiency=92, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:43,650 - {control.data:266} - {INFO:MainThread} - et2 EvTemplateData(name='BMW 225xe', max_current_multi_phases=16, max_phases=1, phase_switch_pause=50, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=20000, min_current=6, max_current_single_phase=16, battery_capacity=6000, efficiency=100, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:43,651 - {control.data:245} - {INFO:MainThread} - general_data GeneralData(chargemode_config=ChargemodeConfig(instant_charging=InstantCharging(phases_to_use=3), phase_switch_delay=5, pv_charging=PvCharging(bat_power_reserve=0, bat_power_reserve_active=False, control_range=[-500, 500], feed_in_yield=15000, phase_switch_delay=7, phases_to_use=1, bat_power_discharge=0, bat_power_discharge_active=False, min_bat_soc=50, bat_mode='ev_mode', switch_off_delay=60, switch_off_threshold=300, switch_on_delay=6, switch_on_threshold=1400), retry_failed_phase_switches=True, scheduled_charging=ScheduledCharging(phases_to_use=0, phases_to_use_pv=0), time_charging=TimeCharging(phases_to_use=3), unbalanced_load_limit=20, unbalanced_load=True), control_interval=10, extern_display_mode='local', extern=False, external_buttons_hw=False, grid_protection_active=False, grid_protection_configured=True, grid_protection_random_stop=0, grid_protection_timestamp=None, http_api=False, mqtt_bridge=False, prices=Prices(bat=0.0003, cp=0, grid=0.0003, pv=0.00012), range_unit='km', ripple_control_receiver=RippleControlReceiver(get=RippleControlReceiverGet(fault_state=0, fault_str='Kein Fehler.', override_value=100), module={'name': 'openWB Dimm- & Control-Kit', 'type': 'dimm_kit', 'configuration': {'ip_address': '192.168.0.158', 'port': 8899, 'modbus_id': 1}}, override_reference=<OverrideReference.CHARGEPOINT: 'chargepoint'>)) 2024-08-27 15:38:43,652 - {control.data:246} - {INFO:MainThread} - general_data-display local 2024-08-27 15:38:43,653 - {control.data:247} - {INFO:MainThread} - graph_data GraphData(config=Config(duration=120)) 2024-08-27 15:38:43,654 - {control.data:248} - {INFO:MainThread} - optional_data OptionalData(et=Et(get=EtGet(fault_state=0, fault_str='Kein Fehler.', prices={})), int_display=InternalDisplay(active=False, on_if_plugged_in=True, pin_active=False, pin_code='0000', standby=60, theme=<modules.display_themes.cards.config.CardsDisplayTheme object at 0x6f089a30>), led=Led(active=False), rfid=Rfid(active=True)) 2024-08-27 15:38:43,655 - {control.data:266} - {INFO:MainThread} - pv2 PvData(config=Config(max_ac_out=0), get=Get(currents=[0.0, 0.0, 0.0], daily_exported=16285.0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026677.0, fault_state=0, fault_str='Kein Fehler.', power=-2737.2)) 2024-08-27 15:38:43,656 - {control.data:250} - {INFO:MainThread} - pv_all_data PvAllData(config=Config(configured=True), get=Get(daily_exported=16285.0, fault_str='Kein Fehler.', fault_state=0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026677.0, power=-2737.2)) 2024-08-27 15:38:43,660 - {control.data:266} - {INFO:MainThread} - system {'update_in_progress': False, 'perform_update': False, 'backup_cloud': {'backup_before_update': True}, 'ip_address': '192.168.188.43', 'current_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_branch': 'Release', 'current_branch_commit': '2024-08-27 12:33:48 +0200 [a069e0f37]', 'current_missing_commits': ['2024-08-27 12:33:48 +0200 [a069e0f37] - Merge pull request #1843 from openWB/master', '2024-06-04 08:52:24 +0200 [417a30647] - Merge pull request #1649 from openWB/master', '2024-03-19 06:56:08 +0100 [a6b648645] - Merge pull request #1490 from openWB/master', '2024-03-14 11:48:27 +0100 [1d1d842c5] - Merge pull request #1367 from openWB/master'], 'boot_done': True, 'datastore_version': 54, 'dataprotection_acknowledged': True, 'usage_terms_acknowledged': True, 'debug_level': 10, 'release_train': 'master', 'version': '2.1.5', 'lastlivevaluesJson': {'timestamp': 1724765913, 'time': '15:38:33', 'grid': 0.092, 'house-power': 0.331, 'charging-all': 2.49, 'pv-all': 2.729, 'cp3-power': 2.49, 'ev1-soc': 72, 'ev2-soc': 68}, 'installAssistantDone': True, 'module_update_completed': True} 2024-08-27 15:38:43,661 - {control.data:279} - {INFO:MainThread} - device0 {'name': 'Hichi', 'type': 'json', 'id': 0, 'configuration': {'url': 'http://192.168.188.23/cm?cmnd=status%2010'}} 2024-08-27 15:38:43,664 - {control.data:281} - {INFO:MainThread} - component0 {'name': 'Hichi', 'type': 'counter', 'id': 0, 'configuration': {'jq_power': '.StatusSNS.SM.W', 'jq_exported': '.StatusSNS.SM.WhExported', 'jq_imported': '.StatusSNS.SM.WhImported', 'jq_powers': ['.StatusSNS.SM.W1', '.StatusSNS.SM.W2', '.StatusSNS.SM.W3'], 'jq_currents': [None, None, None]}} 2024-08-27 15:38:43,665 - {control.data:279} - {INFO:MainThread} - device2 {'name': 'Kostal Piko', 'type': 'kostal_steca', 'id': 2, 'configuration': {'ip_address': '192.168.188.27'}} 2024-08-27 15:38:43,667 - {control.data:281} - {INFO:MainThread} - component2 {'name': 'Kostal Piko', 'type': 'inverter', 'id': 2, 'configuration': {'variant_steca': False}} 2024-08-27 15:38:43,668 - {control.data:253} - {INFO:MainThread} - 2024-08-27 15:38:43,670 - {control.algorithm.algorithm:25} - {INFO:MainThread} - # Algorithmus 2024-08-27 15:38:43,672 - {control.counter:390} - {DEBUG:MainThread} - LP3 Switch-Off-Threshold prüfen: 55.93W, Schwelle: 300W, freigegebener Ãœberschuss 0W, Einspeisegrenze 0W 2024-08-27 15:38:43,674 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:43,675 - {control.algorithm.algorithm:30} - {INFO:MainThread} - **Mindestrom setzen** 2024-08-27 15:38:43,677 - {control.algorithm.min_current:20} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:43,679 - {control.counter:179} - {DEBUG:MainThread} - Zähler 0: [45.370000000000005, 39.29, 39.68]A verbleibende Ströme, 28064.14W verbleibende Leistung 2024-08-27 15:38:43,680 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 6A 2024-08-27 15:38:43,682 - {control.algorithm.algorithm:32} - {INFO:MainThread} - **Sollstrom setzen** 2024-08-27 15:38:43,684 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:43,686 - {control.counter:501} - {DEBUG:MainThread} - Zähler 0: Begrenzung der verbleibenden Leistung auf 1064.1399999999994W 2024-08-27 15:38:43,687 - {control.algorithm.algorithm:38} - {INFO:MainThread} - **PV-geführten Strom setzen** 2024-08-27 15:38:43,690 - {control.algorithm.filter_chargepoints:102} - {DEBUG:MainThread} - Geordnete Ladepunkte [3] 2024-08-27 15:38:43,691 - {control.algorithm.surplus_controlled:45} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:43,692 - {control.loadmanagement:76} - {DEBUG:MainThread} - Leistungsüberschreitung auf 1064.1399999999994W korrigieren: [10.0, 0.0, 0.0] 2024-08-27 15:38:43,693 - {control.algorithm.surplus_controlled:121} - {DEBUG:MainThread} - Ungenutzten Sollstrom aufschlagen ergibt 11.616695652173911A. 2024-08-27 15:38:43,695 - {control.counter:186} - {DEBUG:MainThread} - Zähler 0: [39.753304347826095, 39.29, 39.68]A verbleibende Ströme, -227.70000000000027W verbleibender Ãœberschuss 2024-08-27 15:38:43,696 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 11.616695652173911A 2024-08-27 15:38:43,698 - {control.process:23} - {INFO:MainThread} - # Ladung starten. 2024-08-27 15:38:43,705 - {control.process:109} - {INFO:MainThread} - LP3: set current 11.62 A, state CHARGING_ALLOWED 2024-08-27 15:38:43,707 - {modules.common.component_context:25} - {DEBUG:set current cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:43,982 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/power, Payload 2500.07, vorherige Payload: 2490.21 2024-08-27 15:38:43,984 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/imported, Payload 2713912.11, vorherige Payload: 2713904.05 2024-08-27 15:38:43,988 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/home_consumption, Payload 293.05999999999966, vorherige Payload: 331.25000000000006 2024-08-27 15:38:43,990 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/imported_home_consumption, Payload 2741413.4980709245, vorherige Payload: 2741412.6065495466 2024-08-27 15:38:46,000 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:50,012 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:50,015 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=handler10Sec, args=(), kwargs={})
Dass die Sollstromstärke nur geändert wird, wenn der Regelbereich verlassen wird, ist so nicht im Hilfetext erklärt und auch nicht so umgesetzt. Es wird nicht nachgeregelt, aber auf kleine Schwankungen wird trotzdem reagiert.
Re: Rückmeldungen 2.1.5 Release
Kannst Du bitte ein Ticket öffnen? Ich würde mir das gerne per Remotesupport ansehen.Daphne hat geschrieben: ↑Di Aug 27, 2024 4:55 pm Ich habe heute das Master 2.1.5 eingespielt.
Da tritt folgendes auf:
2024-08-27 18_48_40-openWB.jpg
Vorher bei Master 2.1.5 Beta war das nicht so.Code: Alles auswählen
rc.local bug not found no factory reset pending, normal startup atreboot.sh started checking init in /boot/config.txt... watchdog for atreboot.sh on pid 420 started, waiting for 900s already up to date checking ramdisk settings in /etc/fstab... already up to date Group membership... Final group membership: openwb : openwb adm dialout cdrom sudo audio video plugdev games users input render netdev spi i2c gpio Network... Wait for connection...RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable .RTNETLINK answers: Network is unreachable . my primary IP: 192.168.178.71 my primary interface: eth0 running as primary, enabling plug'n'play network apt configuration already up to date install required packages with 'apt-get'... OK:1 http://archive.raspberrypi.org/debian bullseye InRelease OK:2 http://raspbian.raspberrypi.org/raspbian bullseye InRelease Paketlisten werden gelesen… Paketlisten werden gelesen… Abhängigkeitsbaum wird aufgebaut… Statusinformationen werden eingelesen… accountsservice ist schon die neueste Version (0.6.55-3). apache2 ist schon die neueste Version (2.4.61-1~deb11u1). bc ist schon die neueste Version (1.07.1-2+b1). chromium ist schon die neueste Version (106.0.5249.119-1~deb11u1). chromium-l10n ist schon die neueste Version (106.0.5249.119-1~deb11u1). git ist schon die neueste Version (1:2.30.2-1+deb11u2). jq ist schon die neueste Version (1.6-2.1). libapache2-mod-php ist schon die neueste Version (2:7.4+76). lightdm-autologin-greeter ist schon die neueste Version (1.0-3). mmc-utils ist schon die neueste Version (0+git20180327.b4fe0c8c-1). mosquitto ist schon die neueste Version (2.0.11-1+deb11u1). mosquitto-clients ist schon die neueste Version (2.0.11-1+deb11u1). openbox-lxde-session ist schon die neueste Version (0.99.2-4). php ist schon die neueste Version (2:7.4+76). php-curl ist schon die neueste Version (2:7.4+76). php-gd ist schon die neueste Version (2:7.4+76). php-json ist schon die neueste Version (2:7.4+76). php-xml ist schon die neueste Version (2:7.4+76). socat ist schon die neueste Version (1.7.4.1-3). sshpass ist schon die neueste Version (1.09-1). ssl-cert ist schon die neueste Version (1.1.0+nmu1). sudo ist schon die neueste Version (1.9.5p2-3+deb11u1). vim ist schon die neueste Version (2:8.2.2434-3+deb11u1). x11-xserver-utils ist schon die neueste Version (7.7+8). xserver-xorg ist schon die neueste Version (1:7.7+22). lightdm ist schon die neueste Version (1.26.0-7+rpt1). python3-pip ist schon die neueste Version (20.3.4-4+rpt1+deb11u1). 0 aktualisiert, 0 neu installiert, 0 zu entfernen und 132 nicht aktualisiert. done openwb.cron already up to date openwb2.service definition is already a symlink openwbRemoteSupport.service already up to date no restore pending, normal startup cleaning obsolete python cache folders... python cache cleanup done display setup... autologin configured mouse cursor configured lxde session autostart already configured checking required apache modules... module 'headers' already enabled module 'ssl' already enabled module 'proxy_wstunnel' already enabled apache default site... /etc/apache2/sites-available/000-default.conf is up to date apache default ssl site... /etc/apache2/sites-available/apache-openwb-ssl.conf is up to date apache http api ssl site... /etc/apache2/sites-available/http-api-ssl.conf is up to date site 'default-ssl' already disabled site 'apache-openwb-ssl' already enabled http api is disabled site 'http-api-ssl' already disabled apache configuration is already up to date check mosquitto installation... mosquitto.conf already up to date mosquitto openwb.conf already up to date mosquitto acl already up to date mosquitto_local service definition already up to date mosquitto_local.conf already up to date mosquitto openwb_local.conf already up to date mosquitto done install required python packages with 'pip3'... Looking in indexes: https://pypi.org/simple, https://www.piwheels.org/simple Requirement already satisfied: typing-extensions==4.4.0 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 1)) (4.4.0) Requirement already satisfied: jq==1.1.3 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 2)) (1.1.3) Requirement already satisfied: paho_mqtt==1.6.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 3)) (1.6.1) Requirement already satisfied: pymodbus==2.5.2 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 4)) (2.5.2) Requirement already satisfied: pytest==6.2.5 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 5)) (6.2.5) Requirement already satisfied: requests_mock==1.9.3 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 6)) (1.9.3) Requirement already satisfied: lxml==4.9.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 7)) (4.9.1) Requirement already satisfied: aiohttp==3.9.4 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 8)) (3.9.4) Requirement already satisfied: schedule==1.1.0 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 9)) (1.1.0) Requirement already satisfied: PyJWT==2.6.0 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 10)) (2.6.0) Requirement already satisfied: ipparser==0.3.8 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 11)) (0.3.8) Requirement already satisfied: bs4==0.0.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 12)) (0.0.1) Requirement already satisfied: pkce==1.0.3 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 13)) (1.0.3) Requirement already satisfied: evdev==1.5.0 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 15)) (1.5.0) Requirement already satisfied: cryptography==42.0.4 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 17)) (42.0.4) Requirement already satisfied: msal==1.27.0 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 18)) (1.27.0) Requirement already satisfied: python-dateutil==2.8.2 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 19)) (2.8.2) Requirement already satisfied: umodbus==1.0.4 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 20)) (1.0.4) Requirement already satisfied: pysmb==1.2.9.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 21)) (1.2.9.1) Requirement already satisfied: pytz==2023.3.post1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 22)) (2023.3.post1) Requirement already satisfied: grpcio==1.60.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 23)) (1.60.1) Requirement already satisfied: protobuf==4.25.3 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 24)) (4.25.3) Requirement already satisfied: bimmer_connected==0.15.1 in /home/openwb/.local/lib/python3.9/site-packages (from -r /var/www/html/openWB/requirements.txt (line 25)) (0.15.1) Requirement already satisfied: frozenlist>=1.1.1 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (1.4.1) Requirement already satisfied: multidict<7.0,>=4.5 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (6.0.2) Requirement already satisfied: attrs>=17.3.0 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (22.1.0) Requirement already satisfied: aiosignal>=1.1.2 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (1.3.1) Requirement already satisfied: yarl<2.0,>=1.0 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (1.8.1) Requirement already satisfied: async-timeout<5.0,>=4.0 in /home/openwb/.local/lib/python3.9/site-packages (from aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (4.0.3) Requirement already satisfied: httpx in /home/openwb/.local/lib/python3.9/site-packages (from bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (0.27.0) Requirement already satisfied: pycryptodome>=3.4 in /home/openwb/.local/lib/python3.9/site-packages (from bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (3.20.0) Requirement already satisfied: Pillow in /usr/lib/python3/dist-packages (from bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (8.1.2) Requirement already satisfied: beautifulsoup4 in /home/openwb/.local/lib/python3.9/site-packages (from bs4==0.0.1->-r /var/www/html/openWB/requirements.txt (line 12)) (4.11.1) Requirement already satisfied: cffi>=1.12 in /home/openwb/.local/lib/python3.9/site-packages (from cryptography==42.0.4->-r /var/www/html/openWB/requirements.txt (line 17)) (1.16.0) Requirement already satisfied: dnspython in /home/openwb/.local/lib/python3.9/site-packages (from ipparser==0.3.8->-r /var/www/html/openWB/requirements.txt (line 11)) (2.3.0) Requirement already satisfied: requests<3,>=2.0.0 in /usr/lib/python3/dist-packages (from msal==1.27.0->-r /var/www/html/openWB/requirements.txt (line 18)) (2.25.1) Requirement already satisfied: six>=1.15.0 in /usr/lib/python3/dist-packages (from pymodbus==2.5.2->-r /var/www/html/openWB/requirements.txt (line 4)) (1.16.0) Requirement already satisfied: pyserial>=3.4 in /home/openwb/.local/lib/python3.9/site-packages (from pymodbus==2.5.2->-r /var/www/html/openWB/requirements.txt (line 4)) (3.5) Requirement already satisfied: pyasn1 in /home/openwb/.local/lib/python3.9/site-packages (from pysmb==1.2.9.1->-r /var/www/html/openWB/requirements.txt (line 21)) (0.5.1) Requirement already satisfied: tqdm in /home/openwb/.local/lib/python3.9/site-packages (from pysmb==1.2.9.1->-r /var/www/html/openWB/requirements.txt (line 21)) (4.66.1) Requirement already satisfied: py>=1.8.2 in /home/openwb/.local/lib/python3.9/site-packages (from pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (1.11.0) Requirement already satisfied: pluggy<2.0,>=0.12 in /home/openwb/.local/lib/python3.9/site-packages (from pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (1.0.0) Requirement already satisfied: iniconfig in /home/openwb/.local/lib/python3.9/site-packages (from pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (1.1.1) Requirement already satisfied: toml in /usr/lib/python3/dist-packages (from pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (0.10.1) Requirement already satisfied: packaging in /home/openwb/.local/lib/python3.9/site-packages (from pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (21.3) Requirement already satisfied: pycparser in /home/openwb/.local/lib/python3.9/site-packages (from cffi>=1.12->cryptography==42.0.4->-r /var/www/html/openWB/requirements.txt (line 17)) (2.21) Requirement already satisfied: idna>=2.0 in /usr/lib/python3/dist-packages (from yarl<2.0,>=1.0->aiohttp==3.9.4->-r /var/www/html/openWB/requirements.txt (line 8)) (2.10) Requirement already satisfied: soupsieve>1.2 in /home/openwb/.local/lib/python3.9/site-packages (from beautifulsoup4->bs4==0.0.1->-r /var/www/html/openWB/requirements.txt (line 12)) (2.3.2.post1) Requirement already satisfied: sniffio in /home/openwb/.local/lib/python3.9/site-packages (from httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (1.3.1) Requirement already satisfied: httpcore==1.* in /home/openwb/.local/lib/python3.9/site-packages (from httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (1.0.5) Requirement already satisfied: anyio in /home/openwb/.local/lib/python3.9/site-packages (from httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (4.4.0) Requirement already satisfied: certifi in /usr/lib/python3/dist-packages (from httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (2020.6.20) Requirement already satisfied: h11<0.15,>=0.13 in /home/openwb/.local/lib/python3.9/site-packages (from httpcore==1.*->httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (0.14.0) Requirement already satisfied: exceptiongroup>=1.0.2 in /home/openwb/.local/lib/python3.9/site-packages (from anyio->httpx->bimmer_connected==0.15.1->-r /var/www/html/openWB/requirements.txt (line 25)) (1.2.1) Requirement already satisfied: pyparsing!=3.0.5,>=2.0.2 in /home/openwb/.local/lib/python3.9/site-packages (from packaging->pytest==6.2.5->-r /var/www/html/openWB/requirements.txt (line 5)) (3.0.9) done load versions... chgrp: Zugriff auf '/var/www/html/openWB/data/restore/*' nicht möglich: Datei oder Verzeichnis nicht gefunden chgrp: Zugriff auf '/var/www/html/openWB/data/data_migration/*' nicht möglich: Datei oder Verzeichnis nicht gefunden chmod: Zugriff auf '/var/www/html/openWB/data/restore/*' nicht möglich: Datei oder Verzeichnis nicht gefunden chmod: Zugriff auf '/var/www/html/openWB/data/data_migration/*' nicht möglich: Datei oder Verzeichnis nicht gefunden 2024-08-27 17:59:07: boot done :-) 2024-08-27 17:59:09,816 - {root:179} - {DEBUG:MainThread} - Start openWB2.service 2024-08-27 17:59:09,818 - {helpermodules.update_config:525} - {DEBUG:MainThread} - Broker-Konfiguration aktualisieren 2024-08-27 17:59:10,955 - {helpermodules.update_config:612} - {DEBUG:MainThread} - current datastore version: 54 2024-08-27 17:59:10,956 - {helpermodules.update_config:613} - {DEBUG:MainThread} - target datastore version: 54 2024-08-27 17:59:11,406 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/isss/heartbeat 2024-08-27 17:59:11,409 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/isss/parentWB 2024-08-27 17:59:11,412 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/isss/parentCPlp1 2024-08-27 17:59:11,414 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/isss/Current 2024-08-27 17:59:11,417 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/backup_cloud/None/get/fault_str 2024-08-27 17:59:11,420 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/set/backup_cloud/None/get/fault_state 2024-08-27 17:59:11,603 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/internal_chargepoint/0/get/voltages 2024-08-27 17:59:11,606 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/internal_chargepoint/0/get/currents 2024-08-27 17:59:11,609 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/internal_chargepoint/0/get/frequency 2024-08-27 17:59:11,612 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/internal_chargepoint/0/get/power_factors 2024-08-27 17:59:11,615 - {helpermodules.update_config:569} - {DEBUG:MainThread} - Ungültiges Topic zum Startzeitpunkt: openWB/internal_chargepoint/0/get/imported 2024-08-27 17:59:20,774 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 17:59:20,774 - {helpermodules.setdata:46} - {DEBUG:Setdata} - Subdata initialization completed. Starting setdata loop to broker. 2024-08-27 17:59:20,780 - {modules.common.component_context:25} - {DEBUG:Subdata} - Update Komponente ['OneDrive'] 2024-08-27 17:59:20,823 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten [] 2024-08-27 17:59:20,824 - {modules.common.component_context:25} - {DEBUG:set values cp6} - Update Komponente ['Ladepunkt'] 2024-08-27 17:59:20,926 - {modules.loadvars:75} - {ERROR:MainThread} - Fehler im loadvars-Modul bei Element {'type': 'inverter', 'id': 3} Traceback (most recent call last): File "/var/www/html/openWB/packages/modules/loadvars.py", line 69, in _update_values_of_level component = get_component_obj_by_id(element["id"], not_finished_threads) File "/var/www/html/openWB/packages/modules/common/utils/component_parser.py", line 32, in get_component_obj_by_id if module_data[f"{type_to_topic_mapping(type)}{id}"].data.get.fault_state == 2: KeyError: 'pv3' 2024-08-27 17:59:20,938 - {modules.loadvars:75} - {ERROR:MainThread} - Fehler im loadvars-Modul bei Element {'type': 'bat', 'id': 5} Traceback (most recent call last): File "/var/www/html/openWB/packages/modules/loadvars.py", line 69, in _update_values_of_level component = get_component_obj_by_id(element["id"], not_finished_threads) File "/var/www/html/openWB/packages/modules/common/utils/component_parser.py", line 32, in get_component_obj_by_id if module_data[f"{type_to_topic_mapping(type)}{id}"].data.get.fault_state == 2: KeyError: 'bat5' 2024-08-27 17:59:20,940 - {modules.common.component_context:25} - {DEBUG:update values cp6} - Update Komponente ['Ladepunkt'] 2024-08-27 17:59:21,037 - {modules.common.utils.component_parser:33} - {ERROR:MainThread} - Fehlerstatus in Komponente LG ESS V1.0 Zähler. Werte werden nicht aktualisiert. 2024-08-27 17:59:21,067 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['GPIOs auf der AddOn-Platine'] 2024-08-27 17:59:21,069 - {modules.ripple_control_receivers.gpio.ripple_control_receiver:35} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: False, RSE-Kontakt 2: False 2024-08-27 17:59:21,070 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 17:59:21,075 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['GPIOs auf der AddOn-Platine'] 2024-08-27 17:59:21,076 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 17:59:21,252 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 1: [35.0, 35.0, 35.0]A 2024-08-27 17:59:21,264 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 1: 24000W 2024-08-27 17:59:21,268 - {control.chargepoint.chargepoint:83} - {INFO:MainThread} - LP 6: Ladepunkt gesperrt, da keine Werte vom EVU- oder Zwischenzähler-Zähler empfangen wurden und deshalb kein Lastmanagement durchgeführt werden kann. Bitte schaue auf der Status-Seite nach Fehlermeldungen bei den Zählern. Falls Du dennoch laden möchtest, kannst Du als Gerät 'Virtuelles Gerät' mit einer Komponente 'Virtueller Zähler' verwenden. 2024-08-27 17:59:21,276 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724774284.4942179, power=7738.0, imported=4049963.7965801256, exported=82.9116493656238) 2024-08-27 17:59:21,279 - {modules.common.simcount._simcount:51} - {WARNING:MainThread} - Time difference between previous state and current state is too large. Set time difference to control interval. 2024-08-27 17:59:21,280 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00277778, power1: 7738, power2: 7738 2024-08-27 17:59:21,281 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 21.4944 2024-08-27 17:59:21,284 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 21.4944 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724774361.2759526, power=7738.0, imported=4049985.29102457, exported=82.9116493656238) 2024-08-27 17:59:21,286 - {control.data:266} - {INFO:MainThread} - bat5 BatData(get=Get(currents=[0.0, 0.0, 0.0], soc=100, daily_exported=4103.0, daily_imported=8497.0, imported=1361537.04, exported=1136853.95, fault_state=2, fault_str='OSError None: Unbekannter Fehler None', power=0.0)) 2024-08-27 17:59:21,290 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=True), get=Get(soc=0, daily_exported=4103.0, daily_imported=8497.0, fault_str='Bitte die Statusmeldungen der Speicher prüfen. Es konnte kein aktueller Zählerstand ermittelt werden, da nicht alle Module Werte liefern.', fault_state=2, imported=1361537.04, exported=1136853.95, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 17:59:21,294 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=0.0, daily_exported=0.0, power=0, imported=5354146.0, exported=0)) 2024-08-27 17:59:21,297 - {control.data:266} - {INFO:MainThread} - cp6 ChargepointData(control_parameter=ControlParameter(chargemode='stop', current_plan=None, failed_phase_switches=0, imported_at_plan_start=None, imported_instant_charging=None, limit=None, phases=0, prio=False, required_current=0, required_currents=[0.0, 0.0, 0.0], state=0, submode='stop', timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=False, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=74), currents=[0.0, 0.0, 0.0], daily_imported=0.0, daily_exported=0.0, evse_current=0, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=5354146.0, phases_in_use=0, plug_state=False, power=0, rfid_timestamp=None, rfid=None, serial_number='21262168', soc=None, soc_timestamp=None, state_str="Ladepunkt gesperrt, da keine Werte vom EVU- oder Zwischenzähler-Zähler empfangen wurden und deshalb kein Lastmanagement durchgeführt werden kann. Bitte schaue auf der Status-Seite nach Fehlermeldungen bei den Zählern. Falls Du dennoch laden möchtest, kannst Du als Gerät 'Virtuelles Gerät' mit einer Komponente 'Virtueller Zähler' verwenden.", vehicle_id=None, voltages=[240.21, 239.98, 240.63]), set=Set(charging_ev=-1, charging_ev_prev=-1, current=0, energy_to_charge=0, loadmanagement_available=False, log=Log(chargemode_log_entry='_', costs=0, imported_at_mode_switch=0, imported_at_plugtime=0, imported_since_mode_switch=0, imported_since_plugged=0, range_charged=0, time_charged='00:00', timestamp_start_charging=None, ev=-1, prio=False, rfid=None, serial_number=None, soc_at_start=None, soc_at_end=None, range_at_start=None, range_at_end=None), manual_lock=False, phases_to_use=3, plug_state_prev=False, plug_time=None, required_power=0, rfid=None, target_current=0, charging_ev_data=<control.ev.Ev object at 0x6fb8f100>), config=Config(configuration={'mode': 'series', 'ip_address': 'localhost', 'duo_num': 0}, ev=1, name='Garage', type='internal_openwb', template=0, connected_phases=3, phase_1=1, auto_phase_switch_hw=True, control_pilot_interruption_hw=False, id=6)) 2024-08-27 17:59:21,299 - {control.data:266} - {INFO:MainThread} - cpt0 CpTemplateData(autolock=Autolock(active=False, plans={'0': AutolockPlan(active=False, frequency=Frequency(selected='daily', once=['2021-11-01', '2021-11-05'], weekly=[False, False, False, False, False, False, False]), time=['06:00', '07:00'], name='Standard Autolock-Plan')}, wait_for_charging_end=False), id=0, max_current_multi_phases=16, max_current_single_phase=16, name='Standard Ladepunkt-Profil', disable_after_unplug=False, valid_tags=[]) 2024-08-27 17:59:21,300 - {control.data:266} - {INFO:MainThread} - counter1 CounterData(config=Config(max_currents=[35, 35, 35], max_total_power=24000), get=Get(powers=[0.0, 0.0, 0.0], currents=[0.0, 0.0, 0.0], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], frequency=50, daily_exported=27434.0, daily_imported=1882.0, imported=318564.0967209748, exported=2934568.4161055097, fault_state=2, fault_str='OSError None: Unbekannter Fehler None', power=0), set=Set(error_counter=5, reserved_surplus=0, released_surplus=0, raw_power_left=24000, raw_currents_left=[35.0, 35.0, 35.0], surplus_power_left=0)) 2024-08-27 17:59:21,302 - {control.data:241} - {INFO:MainThread} - counter_all_data CounterAllData(config=Config(home_consumption_source_id=None, reserve_for_not_charging=True), get=Get(hierarchy=[{'id': 1, 'type': 'counter', 'children': [{'id': 3, 'type': 'inverter', 'children': []}, {'id': 5, 'type': 'bat', 'children': []}, {'id': 6, 'type': 'cp', 'children': []}]}]), set=Set(loadmanagement_active=False, home_consumption=7738.0, smarthome_power_excluded_from_home_consumption=0, invalid_home_consumption=0, daily_yield_home_consumption=30550.0, imported_home_consumption=4049985.29102457, disengageable_smarthome_power=0)) 2024-08-27 17:59:21,304 - {control.data:266} - {INFO:MainThread} - ct0 ChargeTemplateData(name='Standard-Lade-Profil', prio=False, load_default=False, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={'0': TimeChargingPlan(active=False, frequency=Frequency(selected='once', once=['2021-11-01', '2021-11-05'], weekly=[False, False, False, False, False, False, False]), time=['06:00', '07:00'], name='Zeitladen-Standard', current=16, limit=Limit(selected='none', amount=1000, soc=50))}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=6, min_current=0, feed_in_limit=False, min_soc=0, max_soc=101), scheduled_charging=ScheduledCharging(plans={}), instant_charging=InstantCharging(current=6, limit=Limit(selected='soc', amount=1000, soc=95)))) 2024-08-27 17:59:21,306 - {control.data:266} - {INFO:MainThread} - ev0 EvData(set=Set(soc_error_counter=1), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 17:59:21,307 - {control.data:266} - {INFO:MainThread} - ev1 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Cupra Born', tag_id=[], get=Get(soc=74, soc_timestamp=1724773977.897841, force_soc_update=False, range=278, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 17:59:21,309 - {control.data:266} - {INFO:MainThread} - ev2 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 17:59:21,310 - {control.data:266} - {INFO:MainThread} - et0 EvTemplateData(name='Standard-Fahrzeug-Profil', max_current_multi_phases=32, max_phases=3, phase_switch_pause=2, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=False, control_pilot_interruption_duration=4, average_consump=18000, min_current=6, max_current_single_phase=20, battery_capacity=58000, efficiency=90, nominal_difference=1, keep_charge_active_duration=30) 2024-08-27 17:59:21,316 - {control.data:245} - {INFO:MainThread} - general_data GeneralData(chargemode_config=ChargemodeConfig(instant_charging=InstantCharging(phases_to_use=3), phase_switch_delay=6, pv_charging=PvCharging(bat_power_reserve=1000, bat_power_reserve_active=True, control_range=[0, 230], feed_in_yield=0, phase_switch_delay=7, phases_to_use=0, bat_power_discharge=100, bat_power_discharge_active=False, min_bat_soc=50, bat_mode='bat_mode', switch_off_delay=30, switch_off_threshold=500, switch_on_delay=30, switch_on_threshold=500), retry_failed_phase_switches=True, scheduled_charging=ScheduledCharging(phases_to_use=0, phases_to_use_pv=0), time_charging=TimeCharging(phases_to_use=1), unbalanced_load_limit=18, unbalanced_load=False), control_interval=10, extern_display_mode='primary', extern=False, external_buttons_hw=False, grid_protection_active=False, grid_protection_configured=True, grid_protection_random_stop=0, grid_protection_timestamp=None, http_api=False, mqtt_bridge=False, prices=Prices(bat=0, cp=0, grid=0.000287, pv=7e-05), range_unit='km', ripple_control_receiver=RippleControlReceiver(get=RippleControlReceiverGet(fault_state=0, fault_str='Kein Fehler.', override_value=100), module={'name': 'GPIOs auf der AddOn-Platine', 'type': 'gpio', 'configuration': {}}, override_reference=<OverrideReference.CHARGEPOINT: 'chargepoint'>)) 2024-08-27 17:59:21,318 - {control.data:246} - {INFO:MainThread} - general_data-display primary 2024-08-27 17:59:21,319 - {control.data:247} - {INFO:MainThread} - graph_data GraphData(config=Config(duration=120)) 2024-08-27 17:59:21,323 - {control.data:248} - {INFO:MainThread} - optional_data OptionalData(et=Et(get=EtGet(fault_state=0, fault_str='Kein Fehler.', prices={})), int_display=InternalDisplay(active=True, on_if_plugged_in=True, pin_active=False, pin_code='0000', standby=180, theme=<modules.display_themes.cards.config.CardsDisplayTheme object at 0x6fb82b38>), led=Led(active=False), rfid=Rfid(active=False)) 2024-08-27 17:59:21,324 - {control.data:266} - {INFO:MainThread} - pv3 PvData(config=Config(max_ac_out=10000), get=Get(currents=[0.0, 0.0, 0.0], daily_exported=48493.0, monthly_exported=1520479.1749999998, yearly_exported=7581354.595585294, exported=7749118.943, fault_state=2, fault_str='OSError None: Unbekannter Fehler None', power=-7738.0)) 2024-08-27 17:59:21,326 - {control.data:250} - {INFO:MainThread} - pv_all_data PvAllData(config=Config(configured=True), get=Get(daily_exported=48493.0, fault_str='Bitte die Statusmeldungen der Wechselrichter prüfen. Es konnte kein aktueller Zählerstand ermittelt werden, da nicht alle Module Werte liefern.', fault_state=2, monthly_exported=1520479.1749999998, yearly_exported=7581354.595585294, exported=7749118.943, power=0)) 2024-08-27 17:59:21,327 - {control.data:266} - {INFO:MainThread} - system {'update_in_progress': False, 'perform_update': False, 'backup_cloud': {'backup_before_update': True}, 'ip_address': '192.168.178.71', 'current_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_branch': 'master', 'current_branch_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_missing_commits': [], 'datastore_version': 54, 'dataprotection_acknowledged': True, 'usage_terms_acknowledged': True, 'debug_level': 10, 'release_train': 'master', 'version': '2.1.5', 'boot_done': True, 'lastlivevaluesJson': {'timestamp': 1724774284, 'time': '17:58:04', 'house-power': 7.738, 'charging-all': 0.0, 'pv-all': -0.0, 'cp6-power': 0.0, 'ev1-soc': 74, 'bat-all-power': 0.0, 'bat-all-soc': 0}, 'installAssistantDone': True, 'module_update_completed': True} 2024-08-27 17:59:21,330 - {control.data:279} - {INFO:MainThread} - device0 {'name': 'LG ESS V1.0', 'type': 'lg', 'id': 0, 'configuration': {'ip_address': '192.168.178.98', 'password': 'DE2201BKRE0250C0'}} 2024-08-27 17:59:21,333 - {control.data:281} - {INFO:MainThread} - component1 {'name': 'LG ESS V1.0 Zähler', 'type': 'counter', 'id': 1, 'configuration': {}} 2024-08-27 17:59:21,335 - {control.data:281} - {INFO:MainThread} - component3 {'name': 'LG ESS V1.0 Wechselrichter', 'type': 'inverter', 'id': 3, 'configuration': {}} 2024-08-27 17:59:21,337 - {control.data:281} - {INFO:MainThread} - component5 {'name': 'LG ESS V1.0 Speicher', 'type': 'bat', 'id': 5, 'configuration': {}} 2024-08-27 17:59:21,340 - {control.data:253} - {INFO:MainThread} - 2024-08-27 17:59:21,341 - {control.algorithm.algorithm:25} - {INFO:MainThread} - # Algorithmus 2024-08-27 17:59:21,343 - {control.algorithm.algorithm:30} - {INFO:MainThread} - **Mindestrom setzen** 2024-08-27 17:59:21,346 - {control.algorithm.algorithm:32} - {INFO:MainThread} - **Sollstrom setzen** 2024-08-27 17:59:21,349 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 17:59:21,350 - {control.counter:501} - {DEBUG:MainThread} - Zähler 1: Begrenzung der verbleibenden Leistung auf 0W 2024-08-27 17:59:21,352 - {control.algorithm.algorithm:43} - {INFO:MainThread} - **Keine Leistung für PV-geführtes Laden übrig.** 2024-08-27 17:59:21,354 - {control.process:23} - {INFO:MainThread} - # Ladung starten. 2024-08-27 17:59:21,363 - {modules.common.component_context:25} - {DEBUG:set current cp6} - Update Komponente ['Ladepunkt'] 2024-08-27 17:59:21,692 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/imported_home_consumption, Payload 4049985.29102457, vorherige Payload: 4049963.7965801256 2024-08-27 17:59:21,698 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/1/set/error_counter, Payload 5, vorherige Payload: 4 2024-08-27 17:59:25,712 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 17:59:30,727 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 17:59:30,728 - {root:56} - {DEBUG:MainThread} - Don't start multiple instances of smarthome thread. 2024-08-27 17:59:30,728 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=handler10Sec, args=(), kwargs={}) 2024-08-27 17:59:30,729 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 17:59:30,760 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten ['LG ESS V1.0 Zähler', 'LG ESS V1.0 Wechselrichter', 'LG ESS V1.0 Speicher'] 2024-08-27 17:59:30,772 - {urllib3.connectionpool:973} - {DEBUG:device0} - Starting new HTTPS connection (1): 192.168.178.98:443 2024-08-27 17:59:30,776 - {modules.common.component_context:25} - {DEBUG:set values cp6} - Update Komponente ['Ladepunkt'] 2024-08-27 17:59:32,056 - {urllib3.connectionpool:452} - {DEBUG:device0} - https://192.168.178.98:443 "POST /v1/user/essinfo/home HTTP/1.1" 405 None 2024-08-27 17:59:32,065 - {urllib3.connectionpool:973} - {DEBUG:device0} - Starting new HTTPS connection (2): 192.168.178.98:443 2024-08-27 17:59:34,110 - {helpermodules.utils._thread_handler:26} - {ERROR:MainThread} - device0 konnte nicht innerhalb des Timeouts die Werte abfragen, die abgefragten Werte werden nicht in der Regelung verwendet. 2024-08-27 17:59:34,111 - {modules.common.utils.component_parser:25} - {ERROR:MainThread} - Keine aktuellen Werte für Gerät LG ESS V1.0 2024-08-27 17:59:34,112 - {modules.common.utils.component_parser:25} - {ERROR:MainThread} - Keine aktuellen Werte für Gerät LG ESS V1.0 2024-08-27 17:59:34,113 - {modules.common.component_context:25} - {DEBUG:update values cp6} - Update Komponente ['Ladepunkt'] 2024-08-27 17:59:34,127 - {modules.common.utils.component_parser:25} - {ERROR:MainThread} - Keine aktuellen Werte für Gerät LG ESS V1.0 2024-08-27 17:59:34,151 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['GPIOs auf der AddOn-Platine'] 2024-08-27 17:59:34,153 - {modules.ripple_control_receivers.gpio.ripple_control_receiver:35} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: False, RSE-Kontakt 2: False 2024-08-27 17:59:34,153 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 17:59:34,162 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['GPIOs auf der AddOn-Platine'] 2024-08-27 17:59:34,164 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 17:59:34,280 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 1: [35.0, 35.0, 35.0]A 2024-08-27 17:59:34,282 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 1: 24000W 2024-08-27 17:59:34,285 - {control.chargepoint.chargepoint:83} - {INFO:MainThread} - LP 6: Ladepunkt gesperrt, da keine Werte vom EVU- oder Zwischenzähler-Zähler empfangen wurden und deshalb kein Lastmanagement durchgeführt werden kann. Bitte schaue auf der Status-Seite nach Fehlermeldungen bei den Zählern. Falls Du dennoch laden möchtest, kannst Du als Gerät 'Virtuelles Gerät' mit einer Komponente 'Virtueller Zähler' verwenden. 2024-08-27 17:59:34,290 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724774361.2759526, power=7738.0, imported=4049985.29102457, exported=82.9116493656238) 2024-08-27 17:59:34,293 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00361507, power1: 7738, power2: 7738 2024-08-27 17:59:34,298 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 27.9734 2024-08-27 17:59:34,299 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 27.9734 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724774374.2902186, power=7738.0, imported=4050013.2644663523, exported=82.9116493656238) 2024-08-27 17:59:34,306 - {control.data:266} - {INFO:MainThread} - bat5 BatData(get=Get(currents=[0.0, 0.0, 0.0], soc=100, daily_exported=4103.0, daily_imported=8497.0, imported=1361537.04, exported=1136853.95, fault_state=2, fault_str='OSError None: Unbekannter Fehler None', power=0.0)) 2024-08-27 17:59:34,308 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=True), get=Get(soc=0, daily_exported=4103.0, daily_imported=8497.0, fault_str='Bitte die Statusmeldungen der Speicher prüfen. Es konnte kein aktueller Zählerstand ermittelt werden, da nicht alle Module Werte liefern.', fault_state=2, imported=1361537.04, exported=1136853.95, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 17:59:34,309 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=0.0, daily_exported=0.0, power=0, imported=5354146.0, exported=0)) 2024-08-27 17:59:34,311 - {control.data:266} - {INFO:MainThread} - cp6 ChargepointData(control_parameter=ControlParameter(chargemode='stop', current_plan=None, failed_phase_switches=0, imported_at_plan_start=None, imported_instant_charging=None, limit=None, phases=0, prio=False, required_current=0, required_currents=[0.0, 0.0, 0.0], state=0, submode='stop', timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=False, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=74), currents=[0.0, 0.0, 0.0], daily_imported=0.0, daily_exported=0.0, evse_current=0, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=5354146.0, phases_in_use=0, plug_state=False, power=0, rfid_timestamp=None, rfid=None, serial_number='21262168', soc=None, soc_timestamp=None, state_str="Ladepunkt gesperrt, da keine Werte vom EVU- oder Zwischenzähler-Zähler empfangen wurden und deshalb kein Lastmanagement durchgeführt werden kann. Bitte schaue auf der Status-Seite nach Fehlermeldungen bei den Zählern. Falls Du dennoch laden möchtest, kannst Du als Gerät 'Virtuelles Gerät' mit einer Komponente 'Virtueller Zähler' verwenden.", vehicle_id=None, voltages=[240.27, 240.01, 240.29]), set=Set(charging_ev=-1, charging_ev_prev=-1, current=0, energy_to_charge=0, loadmanagement_available=False, log=Log(chargemode_log_entry='_', costs=0, imported_at_mode_switch=0, imported_at_plugtime=0, imported_since_mode_switch=0, imported_since_plugged=0, range_charged=0, time_charged='00:00', timestamp_start_charging=None, ev=-1, prio=False, rfid=None, serial_number=None, soc_at_start=None, soc_at_end=None, range_at_start=None, range_at_end=None), manual_lock=False, phases_to_use=3, plug_state_prev=False, plug_time=None, required_power=0, rfid=None, target_current=0,
Re: Rückmeldungen 2.1.5 Release
Der Heizstab zieht genau so viel Energie wie zu viel geladen wird. Es wird allerdings nur nach EVU-Punkt und Speicherleistung geregelt, der Hausverbrauch ist da irrelevant und damit auch, ob der Heizstab dort eingerechnet wird oder nicht.Gero hat geschrieben: ↑Mi Aug 28, 2024 6:55 am Nun ist wieder morgens und ich kann das, was gestern nicht ins Auto ging, nachladen. Aber die openWB regelt den Ladestrom zu hoch!
lade.jpg
PV sind 8,9kW, Ladesleistung sind 10,2kW. Sollte es daran liegen, dass ich gerade meinen Heizstab in den Hausverbrauch habe rechnen lassen?
Oha, Heizstab ausgeschaltet: (eigentlich hätte der ausgehen müssen, "Ausschaltschwelle anpassen" ist gesetzt)
lade2.jpg
https://paste.openwb.de/5BzyrH2amAh6gvj
edit: Nachgestellt bekomme ich es leider nicht nochmal, mittlerweile kommt zu viel vom Dach als dass der Speicher entladen werden müsste. Der wird nun einfach nur nicht mehr geladen - achso: Lademodus prio Fahrzeug.
Es wird erkannt, dass 2kW Speicherleistung zu viel bezogen wird, allerdings wird im Loglevel Info das Lastmanagement nicht geloggt. Warum zu viel zugeteilt wird, kann ich im Log nicht erkennen.
Am besten bitte das Log mal dauerhaft auf Details mit laufen lassen, dann haben wir nicht immer das Problem, dass ich kein Log mit dem Problem habe.
Re: Rückmeldungen 2.1.5 Release
Im Hilfetext steht "Liegt der Überschuss im vorgegebenen Regelbereich, wird nicht nachgeregelt." Ich bin bisher davon ausgegangen, dass beim Nachregeln der Soll-Strom geändert wird. Liege ich da falsch?
Ich will hier keine Haarspalterei, aber kannst Du bitte den Unterschied zwischen "auf kleine Schwankungen wird trotzdem reagiert" und "Nachregeln" erklären? Es wäre sehr hilfreich, den Algorithmus zu verstehen. Ich habe bereits versucht, den Code zu verstehen, aber mir erschließt sich das nicht. Schön wäre es, wenn ihr den Algorithmus im Wiki erklären könntet.
Dahinter steckt das praktische Problem, dass der Onboard-Charger von meinem BMW 225xe die vielen Sollstromänderungen der openWB nicht toleriert und nach ca. 2 Stunden Ladezeit auf Error geht. PV-geführte Ladung daher nicht möglich. Ich bin deshalb sehr daran interessiert, wie ich die Regelgrenzen so einsetzen kann, dass der Strom wirklich weniger oft nachgestellt wird.
Ich will hier keine Haarspalterei, aber kannst Du bitte den Unterschied zwischen "auf kleine Schwankungen wird trotzdem reagiert" und "Nachregeln" erklären? Es wäre sehr hilfreich, den Algorithmus zu verstehen. Ich habe bereits versucht, den Code zu verstehen, aber mir erschließt sich das nicht. Schön wäre es, wenn ihr den Algorithmus im Wiki erklären könntet.
Dahinter steckt das praktische Problem, dass der Onboard-Charger von meinem BMW 225xe die vielen Sollstromänderungen der openWB nicht toleriert und nach ca. 2 Stunden Ladezeit auf Error geht. PV-geführte Ladung daher nicht möglich. Ich bin deshalb sehr daran interessiert, wie ich die Regelgrenzen so einsetzen kann, dass der Strom wirklich weniger oft nachgestellt wird.
LenaK hat geschrieben: ↑Mi Aug 28, 2024 8:53 amDoch der Regelbereich wird berücksichtigt. Dein Bezug liegt doch auch innerhalb des Regelbereichs.andlem hat geschrieben: ↑Di Aug 27, 2024 2:47 pm Regelgrenzen beim PV-Laden werden nicht berücksichtigt
Um den Fehler offensichtlich zu machen, habe ich diese auf Individuell -500 W und +500 W eingestellt. Die openWB setzt alle 10 s einen neuen Stromwert, obwohl die Regelgrenzen nicht überschritten werden. Ich erwarte, dass der Stromwert nicht nachgeregelt wird, bis die Regelgrenzen überschritten werden. Hier der Auszug aus dem Log über zwei Regelperioden:
Code: Alles auswählen
2024-08-27 15:38:30,236 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 15:38:30,333 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten ['Hichi'] 2024-08-27 15:38:30,345 - {modules.common.component_context:25} - {DEBUG:device2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:30,361 - {urllib3.connectionpool:227} - {DEBUG:device0} - Starting new HTTP connection (1): 192.168.188.23:80 2024-08-27 15:38:30,379 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:30,388 - {modules.common.component_context:25} - {DEBUG:set values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:30,414 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /measurements.xml HTTP/1.1" 200 None 2024-08-27 15:38:30,430 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: <?xml version='1.0' encoding='UTF-8'?><root><Device Name='PIKO 3.6 MP' Type='Inverter' Serial='755810BL006202240015' BusAddress='1' NetBiosName='INV006202240015' IpAddress='192.168.188.27' DateTime='2024-08-27T15:37:24'><Measurements><Measurement Value='238.872' Unit='V' Type='AC_Voltage'/><Measurement Value='11.443' Unit='A' Type='AC_Current'/><Measurement Value='2729.150' Unit='W' Type='AC_Power'/><Measurement Value='49.991' Unit='Hz' Type='AC_Frequency'/><Measurement Value='418.171' Unit='V' Type='DC_Voltage'/><Measurement Value='6.532' Unit='A' Type='DC_Current'/><Measurement Value='2737.890' Unit='W' Type='DC_Power'/><Measurement Value='40.000' Unit='°C' Type='Temp'/><Measurement Value='nan' Unit='W' Type='Consumption PV'/><Measurement Value='nan' Unit='W' Type='Consumption Grid'/><Measurement Value='nan' Unit='W' Type='GridPower'/><Measurement Value='100.0' Unit='%' Type='Dearting'/></Measurements></Device></root> 2024-08-27 15:38:30,439 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:30,456 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /gen.yield.total.chart.js HTTP/1.1" 200 None 2024-08-27 15:38:30,465 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: var chartData = { "labels": [ "2000","2001","2002","2003","2004","2005","2006","2007","2008","2009","2010","2011","2012","2013","2014","2015","2016","2017","2018","2019","2020","2021","2022","2023","2024"], "datasets": [ { "strokeColor": style_strokecolor.color, "fillColor": style_fillcolor.color, "data": [ 0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000, 0.000000,0.000000,2.326921,4.263654,4.414874,4.505618,4.035070,4.734527,4.436030,3.309975] } ] } var max = 5; var steps = 5; document.getElementById("labelValueId").innerHTML = " 32.031MWh"; var myBar = new Chart(document.getElementById("canvasId") .getContext("2d")) .Bar(chartData, { "pointDot": false, "datasetFill": false, "scaleOverride": true, "scaleLabel": "<%=value%> MWh", "scaleSteps": steps, "scaleStartValue": 0, "scaleStepWidth": Math.ceil(max / steps), "scaleLineColor": style_linecolor.color, "scaleFontColor": style_fontcolor.color }); 2024-08-27 15:38:30,478 - {modules.common.store._api:26} - {DEBUG:device2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:30,557 - {urllib3.connectionpool:452} - {DEBUG:device0} - http://192.168.188.23:80 "GET /cm?cmnd=status%2010 HTTP/1.1" 200 None 2024-08-27 15:38:30,560 - {modules.common.req:32} - {DEBUG:device0} - Get-Response: {"StatusSNS":{"Time":"2024-08-27T14:38:31","SM":{"WhImported":16262696.339180,"WhExported":21749651.650630,"W":92.310,"W1":-147.690,"W2":157.690,"W3":82.310}}} 2024-08-27 15:38:32,867 - {modules.common.store._api:26} - {DEBUG:device0} - Raw data CounterState(currents=[-0.6421304347826087, 0.6856086956521739, 0.3578695652173913], powers=[-147.69, 157.69, 82.31], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.33918, exported=21749651.65063, power=92.31, frequency=50) 2024-08-27 15:38:32,893 - {modules.common.component_context:25} - {DEBUG:component2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:32,895 - {modules.common.store._api:26} - {DEBUG:component2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:32,896 - {modules.common.component_context:25} - {DEBUG:update values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:32,897 - {modules.common.store._api:31} - {INFO:component2} - Saving InverterState(currents=[0.0, 0.0, 0.0], power=-2729.15, exported=32026669.0, dc_power=None) 2024-08-27 15:38:32,981 - {modules.common.component_context:25} - {DEBUG:component0} - Update Komponente ['Hichi'] 2024-08-27 15:38:32,982 - {modules.common.store._api:31} - {INFO:component0} - Saving CounterState(currents=[-0.6421304347826087, 0.6856086956521739, 0.3578695652173913], powers=[-147.69, 157.69, 82.31], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.33918, exported=21749651.65063, power=92.31, frequency=50) 2024-08-27 15:38:33,040 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:33,235 - {modules.ripple_control_receivers.dimm_kit.ripple_control_receiver:27} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: State.CLOSED, RSE-Kontakt 2: State.CLOSED 2024-08-27 15:38:33,236 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 15:38:33,240 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:33,242 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 15:38:33,330 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 0: [51.21, 39.29, 39.68]A 2024-08-27 15:38:33,331 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 0: 29397.9W 2024-08-27 15:38:33,332 - {control.ev:909} - {DEBUG:MainThread} - RFID 0011214001 wird EV 2 zugeordnet. 2024-08-27 15:38:33,334 - {control.chargepoint.chargepoint:557} - {DEBUG:MainThread} - EV-Phasenzahl beschränkt die nutzbaren Phasen auf 1 2024-08-27 15:38:33,338 - {control.chargepoint.chargepoint:682} - {INFO:MainThread} - LP 3, EV: BMW 225xe (EV-Nr.2): Theoretisch benötigter Strom 6A, Lademodus pv_charging, Submodus: Chargemode.PV_CHARGING, Phasen: 1, Priorität: False, max. Ist-Strom: 10.57 2024-08-27 15:38:33,343 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724765903.7499952, power=281.4800000000003, imported=2741411.7901248764, exported=0) 2024-08-27 15:38:33,345 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00266488, power1: 281.48, power2: 331.25 2024-08-27 15:38:33,346 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 0.816425 2024-08-27 15:38:33,348 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 0.816425 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724765913.343548, power=331.25000000000006, imported=2741412.6065495466, exported=0) 2024-08-27 15:38:33,350 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=False), get=Get(soc=0, daily_exported=0.0, daily_imported=0.0, fault_str='Kein Fehler.', fault_state=0, imported=0, exported=0, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 15:38:33,353 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=4048.0, daily_exported=0.0, power=2490.21, imported=2713904.05, exported=0)) 2024-08-27 15:38:33,355 - {control.data:266} - {INFO:MainThread} - cp3 ChargepointData(control_parameter=ControlParameter(chargemode=<Chargemode.PV_CHARGING: 'pv_charging'>, current_plan=None, failed_phase_switches=1, imported_at_plan_start=None, imported_instant_charging=None, limit=', da die maximale Leistung an Zähler {} erreicht ist.', phases=1, prio=False, required_current=6, required_currents=[6, 0.0, 0.0], state=4, submode=<Chargemode.PV_CHARGING: 'pv_charging'>, timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=True, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=68), currents=[10.57, -0.02, 0.04], daily_imported=4048.0, daily_exported=0.0, evse_current=1170, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=2713904.05, phases_in_use=1, plug_state=True, power=2490.21, rfid_timestamp=None, rfid=None, serial_number='21299772', soc=None, soc_timestamp=None, state_str=None, vehicle_id=None, voltages=[236.46, 237.2, 238.73]), set=Set(charging_ev=2, charging_ev_prev=2, current=11.7, energy_to_charge=0, loadmanagement_available=True, log=Log(chargemode_log_entry='pv_charging', costs=0, imported_at_mode_switch=2713754.88, imported_at_plugtime=2709708.98, imported_since_mode_switch=143.07000000029802, imported_since_plugged=4188.970000000205, range_charged=0.7153500000014902, time_charged='0:03', timestamp_start_charging=1724765683.492532, ev=2, prio=False, rfid='0011214001', serial_number=None, soc_at_start=65, soc_at_end=None, range_at_start=15.0, range_at_end=None), manual_lock=False, phases_to_use=1, plug_state_prev=True, plug_time=1724688005.191368, required_power=1380.0, rfid='0011214001', target_current=0, charging_ev_data=<control.ev.Ev object at 0x7046ca00>), config=Config(configuration={'mode': 'series', 'ip_address': 'localhost', 'duo_num': 0}, ev=0, name='Interne openWB', type='internal_openwb', template=0, connected_phases=3, phase_1=1, auto_phase_switch_hw=True, control_pilot_interruption_hw=True, id=3)) 2024-08-27 15:38:33,358 - {control.data:266} - {INFO:MainThread} - cpt0 CpTemplateData(autolock=Autolock(active=False, plans={}, wait_for_charging_end=False), id=0, max_current_multi_phases=16, max_current_single_phase=16, name='Standard Ladepunkt-Vorlage', disable_after_unplug=False, valid_tags=['0003411712', '0006721162', '0007501485', '0011214001']) 2024-08-27 15:38:33,359 - {control.data:266} - {INFO:MainThread} - counter0 CounterData(config=Config(max_currents=[40, 40, 40], max_total_power=27000), get=Get(powers=[-147.69, 157.69, 82.31], currents=[-0.64, 0.69, 0.36], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], frequency=50, daily_exported=8194.0, daily_imported=1572.0, imported=16262696.33918, exported=21749651.65063, fault_state=0, fault_str='Kein Fehler.', power=92.31), set=Set(error_counter=0, reserved_surplus=0, released_surplus=0, raw_power_left=29397.9, raw_currents_left=[51.21, 39.29, 39.68], surplus_power_left=0)) 2024-08-27 15:38:33,362 - {control.data:241} - {INFO:MainThread} - counter_all_data CounterAllData(config=Config(home_consumption_source_id=None, reserve_for_not_charging=False), get=Get(hierarchy=[{'id': 0, 'type': 'counter', 'children': [{'id': 2, 'type': 'inverter', 'children': []}, {'id': 3, 'type': 'cp', 'children': []}]}]), set=Set(loadmanagement_active=False, home_consumption=331.25000000000006, smarthome_power_excluded_from_home_consumption=0, invalid_home_consumption=0, daily_yield_home_consumption=5810.0, imported_home_consumption=2741412.6065495466, disengageable_smarthome_power=0)) 2024-08-27 15:38:33,364 - {control.data:266} - {INFO:MainThread} - ct0 ChargeTemplateData(name='Standard-Ladeprofil-Vorlage', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='stop', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:33,367 - {control.data:266} - {INFO:MainThread} - ct1 ChargeTemplateData(name='Corsa', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=6, min_current=0, feed_in_limit=False, min_soc=0, max_soc=70), scheduled_charging=ScheduledCharging(plans={'3': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2024-08-10', weekly=[False, False, False, False, False, False, False]), current=9, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=90, soc_scheduled=90), time='13:00')}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=100)))) 2024-08-27 15:38:33,369 - {control.data:266} - {INFO:MainThread} - ct2 ChargeTemplateData(name='BMW 225xe', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={'2': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2023-11-11', weekly=[False, False, False, False, False, False, False]), current=14, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=100, soc_scheduled=100), time='11:50')}), instant_charging=InstantCharging(current=17, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:33,370 - {control.data:266} - {INFO:MainThread} - ev0 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=True, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,370 - {control.data:266} - {INFO:MainThread} - ev1 EvData(set=Set(soc_error_counter=0), charge_template=1, ev_template=1, name='Corsa', tag_id=['0003411712', '0007501485'], get=Get(soc=72, soc_timestamp=1724765717.317447, force_soc_update=False, range=272, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,372 - {control.data:266} - {INFO:MainThread} - ev2 EvData(set=Set(soc_error_counter=0), charge_template=2, ev_template=2, name='BMW 225xe', tag_id=['0006721162', '0011214001'], get=Get(soc=68, soc_timestamp=1724765685.227685, force_soc_update=False, range=18.0, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,374 - {control.data:266} - {INFO:MainThread} - ev3 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='neues Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:33,375 - {control.data:266} - {INFO:MainThread} - et0 EvTemplateData(name='Standard-Fahrzeug-Vorlage', max_current_multi_phases=16, max_phases=3, phase_switch_pause=2, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=False, control_pilot_interruption_duration=4, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=82000, efficiency=90, nominal_difference=1, keep_charge_active_duration=40) 2024-08-27 15:38:33,383 - {control.data:266} - {INFO:MainThread} - et1 EvTemplateData(name='Corsa', max_current_multi_phases=16, max_phases=3, phase_switch_pause=120, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=46000, efficiency=92, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:33,386 - {control.data:266} - {INFO:MainThread} - et2 EvTemplateData(name='BMW 225xe', max_current_multi_phases=16, max_phases=1, phase_switch_pause=50, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=20000, min_current=6, max_current_single_phase=16, battery_capacity=6000, efficiency=100, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:33,388 - {control.data:245} - {INFO:MainThread} - general_data GeneralData(chargemode_config=ChargemodeConfig(instant_charging=InstantCharging(phases_to_use=3), phase_switch_delay=5, pv_charging=PvCharging(bat_power_reserve=0, bat_power_reserve_active=False, control_range=[-500, 500], feed_in_yield=15000, phase_switch_delay=7, phases_to_use=1, bat_power_discharge=0, bat_power_discharge_active=False, min_bat_soc=50, bat_mode='ev_mode', switch_off_delay=60, switch_off_threshold=300, switch_on_delay=6, switch_on_threshold=1400), retry_failed_phase_switches=True, scheduled_charging=ScheduledCharging(phases_to_use=0, phases_to_use_pv=0), time_charging=TimeCharging(phases_to_use=3), unbalanced_load_limit=20, unbalanced_load=True), control_interval=10, extern_display_mode='local', extern=False, external_buttons_hw=False, grid_protection_active=False, grid_protection_configured=True, grid_protection_random_stop=0, grid_protection_timestamp=None, http_api=False, mqtt_bridge=False, prices=Prices(bat=0.0003, cp=0, grid=0.0003, pv=0.00012), range_unit='km', ripple_control_receiver=RippleControlReceiver(get=RippleControlReceiverGet(fault_state=0, fault_str='Kein Fehler.', override_value=100), module={'name': 'openWB Dimm- & Control-Kit', 'type': 'dimm_kit', 'configuration': {'ip_address': '192.168.0.158', 'port': 8899, 'modbus_id': 1}}, override_reference=<OverrideReference.CHARGEPOINT: 'chargepoint'>)) 2024-08-27 15:38:33,392 - {control.data:246} - {INFO:MainThread} - general_data-display local 2024-08-27 15:38:33,392 - {control.data:247} - {INFO:MainThread} - graph_data GraphData(config=Config(duration=120)) 2024-08-27 15:38:33,393 - {control.data:248} - {INFO:MainThread} - optional_data OptionalData(et=Et(get=EtGet(fault_state=0, fault_str='Kein Fehler.', prices={})), int_display=InternalDisplay(active=False, on_if_plugged_in=True, pin_active=False, pin_code='0000', standby=60, theme=<modules.display_themes.cards.config.CardsDisplayTheme object at 0x70484580>), led=Led(active=False), rfid=Rfid(active=True)) 2024-08-27 15:38:33,394 - {control.data:266} - {INFO:MainThread} - pv2 PvData(config=Config(max_ac_out=0), get=Get(currents=[0.0, 0.0, 0.0], daily_exported=16285.0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026669.0, fault_state=0, fault_str='Kein Fehler.', power=-2729.15)) 2024-08-27 15:38:33,394 - {control.data:250} - {INFO:MainThread} - pv_all_data PvAllData(config=Config(configured=True), get=Get(daily_exported=16285.0, fault_str='Kein Fehler.', fault_state=0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026669.0, power=-2729.15)) 2024-08-27 15:38:33,395 - {control.data:266} - {INFO:MainThread} - system {'update_in_progress': False, 'perform_update': False, 'backup_cloud': {'backup_before_update': True}, 'ip_address': '192.168.188.43', 'current_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_branch': 'Release', 'current_branch_commit': '2024-08-27 12:33:48 +0200 [a069e0f37]', 'current_missing_commits': ['2024-08-27 12:33:48 +0200 [a069e0f37] - Merge pull request #1843 from openWB/master', '2024-06-04 08:52:24 +0200 [417a30647] - Merge pull request #1649 from openWB/master', '2024-03-19 06:56:08 +0100 [a6b648645] - Merge pull request #1490 from openWB/master', '2024-03-14 11:48:27 +0100 [1d1d842c5] - Merge pull request #1367 from openWB/master'], 'boot_done': True, 'datastore_version': 54, 'dataprotection_acknowledged': True, 'usage_terms_acknowledged': True, 'debug_level': 10, 'release_train': 'master', 'version': '2.1.5', 'lastlivevaluesJson': {'timestamp': 1724765903, 'time': '15:38:23', 'grid': -0.177, 'house-power': 0.281, 'charging-all': 2.27, 'pv-all': 2.729, 'cp3-power': 2.27, 'ev1-soc': 72, 'ev2-soc': 68}, 'installAssistantDone': True, 'module_update_completed': True} 2024-08-27 15:38:33,397 - {control.data:279} - {INFO:MainThread} - device0 {'name': 'Hichi', 'type': 'json', 'id': 0, 'configuration': {'url': 'http://192.168.188.23/cm?cmnd=status%2010'}} 2024-08-27 15:38:33,402 - {control.data:281} - {INFO:MainThread} - component0 {'name': 'Hichi', 'type': 'counter', 'id': 0, 'configuration': {'jq_power': '.StatusSNS.SM.W', 'jq_exported': '.StatusSNS.SM.WhExported', 'jq_imported': '.StatusSNS.SM.WhImported', 'jq_powers': ['.StatusSNS.SM.W1', '.StatusSNS.SM.W2', '.StatusSNS.SM.W3'], 'jq_currents': [None, None, None]}} 2024-08-27 15:38:33,404 - {control.data:279} - {INFO:MainThread} - device2 {'name': 'Kostal Piko', 'type': 'kostal_steca', 'id': 2, 'configuration': {'ip_address': '192.168.188.27'}} 2024-08-27 15:38:33,406 - {control.data:281} - {INFO:MainThread} - component2 {'name': 'Kostal Piko', 'type': 'inverter', 'id': 2, 'configuration': {'variant_steca': False}} 2024-08-27 15:38:33,407 - {control.data:253} - {INFO:MainThread} - 2024-08-27 15:38:33,407 - {control.algorithm.algorithm:25} - {INFO:MainThread} - # Algorithmus 2024-08-27 15:38:33,408 - {control.counter:390} - {DEBUG:MainThread} - LP3 Switch-Off-Threshold prüfen: 92.31W, Schwelle: 300W, freigegebener Ãœberschuss 0W, Einspeisegrenze 0W 2024-08-27 15:38:33,411 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:33,413 - {control.algorithm.algorithm:30} - {INFO:MainThread} - **Mindestrom setzen** 2024-08-27 15:38:33,415 - {control.algorithm.min_current:20} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:33,416 - {control.counter:179} - {DEBUG:MainThread} - Zähler 0: [45.21, 39.29, 39.68]A verbleibende Ströme, 28017.9W verbleibende Leistung 2024-08-27 15:38:33,418 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 6A 2024-08-27 15:38:33,419 - {control.algorithm.algorithm:32} - {INFO:MainThread} - **Sollstrom setzen** 2024-08-27 15:38:33,422 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:33,424 - {control.counter:501} - {DEBUG:MainThread} - Zähler 0: Begrenzung der verbleibenden Leistung auf 1017.9000000000015W 2024-08-27 15:38:33,428 - {control.algorithm.algorithm:38} - {INFO:MainThread} - **PV-geführten Strom setzen** 2024-08-27 15:38:33,431 - {control.algorithm.filter_chargepoints:102} - {DEBUG:MainThread} - Geordnete Ladepunkte [3] 2024-08-27 15:38:33,432 - {control.algorithm.surplus_controlled:45} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:33,435 - {control.loadmanagement:76} - {DEBUG:MainThread} - Leistungsüberschreitung auf 1017.9000000000015W korrigieren: [10.0, 0.0, 0.0] 2024-08-27 15:38:33,435 - {control.algorithm.surplus_controlled:121} - {DEBUG:MainThread} - Ungenutzten Sollstrom aufschlagen ergibt 11.55565217391305A. 2024-08-27 15:38:33,436 - {control.counter:186} - {DEBUG:MainThread} - Zähler 0: [39.65434782608695, 39.29, 39.68]A verbleibende Ströme, -259.89999999999986W verbleibender Ãœberschuss 2024-08-27 15:38:33,436 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 11.55565217391305A 2024-08-27 15:38:33,437 - {control.process:23} - {INFO:MainThread} - # Ladung starten. 2024-08-27 15:38:33,438 - {control.process:109} - {INFO:MainThread} - LP3: set current 11.56 A, state CHARGING_ALLOWED 2024-08-27 15:38:33,440 - {modules.common.component_context:25} - {DEBUG:set current cp3} - Update Komponente ['Ladepunkt'] kill: (420): Kein passender Prozess gefunden seems like atreboot.sh finished normally 2024-08-27 15:38:33,729 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/power, Payload 2490.21, vorherige Payload: 2270.37 2024-08-27 15:38:33,731 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/imported, Payload 2713904.05, vorherige Payload: 2713897.95 2024-08-27 15:38:33,733 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/home_consumption, Payload 331.25000000000006, vorherige Payload: 281.4800000000003 2024-08-27 15:38:33,737 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/imported_home_consumption, Payload 2741412.6065495466, vorherige Payload: 2741411.7901248764 2024-08-27 15:38:34,601 - {helpermodules.command:126} - {DEBUG:Commands} - Befehl: {'command': 'getDailyLog', 'data': {'day': '20240827'}}, Connection-ID: rjmkd 2024-08-27 15:38:35,751 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:40,770 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:40,772 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=handler10Sec, args=(), kwargs={}) 2024-08-27 15:38:40,773 - {root:75} - {INFO:MainThread} - # ***Start*** 2024-08-27 15:38:40,808 - {modules.common.component_context:54} - {DEBUG:device0} - Update Komponenten ['Hichi'] 2024-08-27 15:38:40,811 - {modules.common.component_context:25} - {DEBUG:device2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:40,815 - {urllib3.connectionpool:227} - {DEBUG:device0} - Starting new HTTP connection (1): 192.168.188.23:80 2024-08-27 15:38:40,821 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:40,825 - {modules.common.component_context:25} - {DEBUG:set values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:40,833 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /measurements.xml HTTP/1.1" 200 None 2024-08-27 15:38:40,836 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: <?xml version='1.0' encoding='UTF-8'?><root><Device Name='PIKO 3.6 MP' Type='Inverter' Serial='755810BL006202240015' BusAddress='1' NetBiosName='INV006202240015' IpAddress='192.168.188.27' DateTime='2024-08-27T15:37:34'><Measurements><Measurement Value='238.853' Unit='V' Type='AC_Voltage'/><Measurement Value='11.506' Unit='A' Type='AC_Current'/><Measurement Value='2737.200' Unit='W' Type='AC_Power'/><Measurement Value='49.993' Unit='Hz' Type='AC_Frequency'/><Measurement Value='418.430' Unit='V' Type='DC_Voltage'/><Measurement Value='6.547' Unit='A' Type='DC_Current'/><Measurement Value='2744.030' Unit='W' Type='DC_Power'/><Measurement Value='39.900' Unit='°C' Type='Temp'/><Measurement Value='nan' Unit='W' Type='Consumption PV'/><Measurement Value='nan' Unit='W' Type='Consumption Grid'/><Measurement Value='nan' Unit='W' Type='GridPower'/><Measurement Value='100.0' Unit='%' Type='Dearting'/></Measurements></Device></root> 2024-08-27 15:38:40,842 - {urllib3.connectionpool:227} - {DEBUG:device2} - Starting new HTTP connection (1): 192.168.188.27:80 2024-08-27 15:38:40,851 - {urllib3.connectionpool:452} - {DEBUG:device2} - http://192.168.188.27:80 "GET /gen.yield.total.chart.js HTTP/1.1" 200 None 2024-08-27 15:38:40,855 - {modules.common.req:32} - {DEBUG:device2} - Get-Response: var chartData = { "labels": [ "2000","2001","2002","2003","2004","2005","2006","2007","2008","2009","2010","2011","2012","2013","2014","2015","2016","2017","2018","2019","2020","2021","2022","2023","2024"], "datasets": [ { "strokeColor": style_strokecolor.color, "fillColor": style_fillcolor.color, "data": [ 0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000,0.000000, 0.000000,0.000000,2.326921,4.263654,4.414874,4.505618,4.035070,4.734527,4.436030,3.309983] } ] } var max = 5; var steps = 5; document.getElementById("labelValueId").innerHTML = " 32.031MWh"; var myBar = new Chart(document.getElementById("canvasId") .getContext("2d")) .Bar(chartData, { "pointDot": false, "datasetFill": false, "scaleOverride": true, "scaleLabel": "<%=value%> MWh", "scaleSteps": steps, "scaleStartValue": 0, "scaleStepWidth": Math.ceil(max / steps), "scaleLineColor": style_linecolor.color, "scaleFontColor": style_fontcolor.color }); 2024-08-27 15:38:40,856 - {modules.common.store._api:26} - {DEBUG:device2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:40,906 - {urllib3.connectionpool:452} - {DEBUG:device0} - http://192.168.188.23:80 "GET /cm?cmnd=status%2010 HTTP/1.1" 200 None 2024-08-27 15:38:40,908 - {modules.common.req:32} - {DEBUG:device0} - Get-Response: {"StatusSNS":{"Time":"2024-08-27T14:38:41","SM":{"WhImported":16262696.482510,"WhExported":21749651.650630,"W":55.930,"W1":-184.220,"W2":158.010,"W3":82.140}}} 2024-08-27 15:38:43,231 - {modules.common.store._api:26} - {DEBUG:device0} - Raw data CounterState(currents=[-0.8009565217391305, 0.6869999999999999, 0.3571304347826087], powers=[-184.22, 158.01, 82.14], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.48251, exported=21749651.65063, power=55.93, frequency=50) 2024-08-27 15:38:43,237 - {modules.common.component_context:25} - {DEBUG:component2} - Update Komponente ['Kostal Piko'] 2024-08-27 15:38:43,239 - {modules.common.component_context:25} - {DEBUG:update values cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:43,243 - {modules.common.store._api:26} - {DEBUG:component2} - Raw data InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:43,246 - {modules.common.store._api:31} - {INFO:component2} - Saving InverterState(currents=[0.0, 0.0, 0.0], power=-2737.2, exported=32026677.0, dc_power=None) 2024-08-27 15:38:43,269 - {modules.common.component_context:25} - {DEBUG:component0} - Update Komponente ['Hichi'] 2024-08-27 15:38:43,271 - {modules.common.store._api:31} - {INFO:component0} - Saving CounterState(currents=[-0.8009565217391305, 0.6869999999999999, 0.3571304347826087], powers=[-184.22, 158.01, 82.14], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], imported=16262696.48251, exported=21749651.65063, power=55.93, frequency=50) 2024-08-27 15:38:43,320 - {modules.common.component_context:25} - {DEBUG:get ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:43,523 - {modules.ripple_control_receivers.dimm_kit.ripple_control_receiver:27} - {DEBUG:get ripple control receiver} - RSE-Kontakt 1: State.CLOSED, RSE-Kontakt 2: State.CLOSED 2024-08-27 15:38:43,524 - {modules.common.store._api:26} - {DEBUG:get ripple control receiver} - Raw data RcrState(override_value=100) 2024-08-27 15:38:43,526 - {modules.common.component_context:25} - {DEBUG:set ripple control receiver} - Update Komponente ['openWB Dimm- & Control-Kit'] 2024-08-27 15:38:43,527 - {modules.common.store._api:31} - {INFO:set ripple control receiver} - Saving RcrState(override_value=100) 2024-08-27 15:38:43,613 - {control.counter:148} - {INFO:MainThread} - Verbleibende Ströme an Zähler 0: [51.370000000000005, 39.29, 39.68]A 2024-08-27 15:38:43,614 - {control.counter:171} - {INFO:MainThread} - Verbleibende Leistung an Zähler 0: 29444.14W 2024-08-27 15:38:43,615 - {control.ev:909} - {DEBUG:MainThread} - RFID 0011214001 wird EV 2 zugeordnet. 2024-08-27 15:38:43,617 - {control.chargepoint.chargepoint:557} - {DEBUG:MainThread} - EV-Phasenzahl beschränkt die nutzbaren Phasen auf 1 2024-08-27 15:38:43,620 - {control.chargepoint.chargepoint:682} - {INFO:MainThread} - LP 3, EV: BMW 225xe (EV-Nr.2): Theoretisch benötigter Strom 6A, Lademodus pv_charging, Submodus: Chargemode.PV_CHARGING, Phasen: 1, Priorität: False, max. Ist-Strom: 10.57 2024-08-27 15:38:43,625 - {modules.common.simcount._simcount:42} - {DEBUG:MainThread} - Previous state: SimCounterState(timestamp=1724765913.343548, power=331.25000000000006, imported=2741412.6065495466, exported=0) 2024-08-27 15:38:43,626 - {modules.common.simcount._calculate:11} - {DEBUG:MainThread} - time passed: 0.00285602, power1: 331.25, power2: 293.06 2024-08-27 15:38:43,628 - {modules.common.simcount._calculate:27} - {DEBUG:MainThread} - power did not change sign. Total energy: 0.891521 2024-08-27 15:38:43,629 - {modules.common.simcount._simcount:65} - {DEBUG:MainThread} - imported: 0.891521 Wh, exported: 0 Wh, new state: SimCounterState(timestamp=1724765923.6252253, power=293.05999999999966, imported=2741413.4980709245, exported=0) 2024-08-27 15:38:43,630 - {control.data:236} - {INFO:MainThread} - bat_all_data BatAllData(config=Config(configured=False), get=Get(soc=0, daily_exported=0.0, daily_imported=0.0, fault_str='Kein Fehler.', fault_state=0, imported=0, exported=0, power=0), set=Set(charging_power_left=0, regulate_up=False)) 2024-08-27 15:38:43,632 - {control.data:237} - {INFO:MainThread} - cp_all_data AllChargepointData(get=AllGet(daily_imported=4048.0, daily_exported=0.0, power=2500.07, imported=2713912.11, exported=0)) 2024-08-27 15:38:43,634 - {control.data:266} - {INFO:MainThread} - cp3 ChargepointData(control_parameter=ControlParameter(chargemode=<Chargemode.PV_CHARGING: 'pv_charging'>, current_plan=None, failed_phase_switches=1, imported_at_plan_start=None, imported_instant_charging=None, limit=', da die maximale Leistung an Zähler {} erreicht ist.', phases=1, prio=False, required_current=6, required_currents=[6, 0.0, 0.0], state=4, submode=<Chargemode.PV_CHARGING: 'pv_charging'>, timestamp_auto_phase_switch=None, timestamp_perform_phase_switch=None, timestamp_switch_on_off=None), get=Get(charge_state=True, connected_vehicle=ConnectedVehicle(config=ConnectedConfig(average_consumption=17, charge_template=0, chargemode='stop', current_plan=0, ev_template=0, priority=False, time_charging_in_use=False), info=ConnectedInfo(id=0, name='Ladepunkt'), soc=68), currents=[10.57, -0.02, 0.04], daily_imported=4048.0, daily_exported=0.0, evse_current=1156, exported=0, fault_str='Kein Fehler.', fault_state=0, imported=2713912.11, phases_in_use=1, plug_state=True, power=2500.07, rfid_timestamp=None, rfid=None, serial_number='21299772', soc=None, soc_timestamp=None, state_str=None, vehicle_id=None, voltages=[236.57, 237.81, 238.48]), set=Set(charging_ev=2, charging_ev_prev=2, current=11.56, energy_to_charge=0, loadmanagement_available=True, log=Log(chargemode_log_entry='pv_charging', costs=0, imported_at_mode_switch=2713754.88, imported_at_plugtime=2709708.98, imported_since_mode_switch=149.1699999999255, imported_since_plugged=4195.069999999832, range_charged=0.7458499999996274, time_charged='0:03', timestamp_start_charging=1724765683.492532, ev=2, prio=False, rfid='0011214001', serial_number=None, soc_at_start=65, soc_at_end=None, range_at_start=15.0, range_at_end=None), manual_lock=False, phases_to_use=1, plug_state_prev=True, plug_time=1724688005.191368, required_power=1380.0, rfid='0011214001', target_current=0, charging_ev_data=<control.ev.Ev object at 0x70484f40>), config=Config(configuration={'mode': 'series', 'ip_address': 'localhost', 'duo_num': 0}, ev=0, name='Interne openWB', type='internal_openwb', template=0, connected_phases=3, phase_1=1, auto_phase_switch_hw=True, control_pilot_interruption_hw=True, id=3)) 2024-08-27 15:38:43,635 - {control.data:266} - {INFO:MainThread} - cpt0 CpTemplateData(autolock=Autolock(active=False, plans={}, wait_for_charging_end=False), id=0, max_current_multi_phases=16, max_current_single_phase=16, name='Standard Ladepunkt-Vorlage', disable_after_unplug=False, valid_tags=['0003411712', '0006721162', '0007501485', '0011214001']) 2024-08-27 15:38:43,636 - {control.data:266} - {INFO:MainThread} - counter0 CounterData(config=Config(max_currents=[40, 40, 40], max_total_power=27000), get=Get(powers=[-184.22, 158.01, 82.14], currents=[-0.8, 0.69, 0.36], voltages=[230.0, 230.0, 230.0], power_factors=[0.0, 0.0, 0.0], frequency=50, daily_exported=8194.0, daily_imported=1572.0, imported=16262696.48251, exported=21749651.65063, fault_state=0, fault_str='Kein Fehler.', power=55.93), set=Set(error_counter=0, reserved_surplus=0, released_surplus=0, raw_power_left=29444.14, raw_currents_left=[51.370000000000005, 39.29, 39.68], surplus_power_left=0)) 2024-08-27 15:38:43,637 - {control.data:241} - {INFO:MainThread} - counter_all_data CounterAllData(config=Config(home_consumption_source_id=None, reserve_for_not_charging=False), get=Get(hierarchy=[{'id': 0, 'type': 'counter', 'children': [{'id': 2, 'type': 'inverter', 'children': []}, {'id': 3, 'type': 'cp', 'children': []}]}]), set=Set(loadmanagement_active=False, home_consumption=293.05999999999966, smarthome_power_excluded_from_home_consumption=0, invalid_home_consumption=0, daily_yield_home_consumption=5810.0, imported_home_consumption=2741413.4980709245, disengageable_smarthome_power=0)) 2024-08-27 15:38:43,638 - {control.data:266} - {INFO:MainThread} - ct0 ChargeTemplateData(name='Standard-Ladeprofil-Vorlage', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='stop', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:43,640 - {control.data:266} - {INFO:MainThread} - ct1 ChargeTemplateData(name='Corsa', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=6, min_current=0, feed_in_limit=False, min_soc=0, max_soc=70), scheduled_charging=ScheduledCharging(plans={'3': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2024-08-10', weekly=[False, False, False, False, False, False, False]), current=9, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=90, soc_scheduled=90), time='13:00')}), instant_charging=InstantCharging(current=32, limit=Limit(selected='none', amount=1000, soc=100)))) 2024-08-27 15:38:43,641 - {control.data:266} - {INFO:MainThread} - ct2 ChargeTemplateData(name='BMW 225xe', prio=False, load_default=True, et=Et(active=False, max_price=0.0002), time_charging=TimeCharging(active=False, plans={}), chargemode=Chargemode(selected='pv_charging', pv_charging=PvCharging(min_soc_current=10, min_current=0, feed_in_limit=False, min_soc=0, max_soc=100), scheduled_charging=ScheduledCharging(plans={'2': ScheduledChargingPlan(active=True, frequency=Frequency(selected='once', once='2023-11-11', weekly=[False, False, False, False, False, False, False]), current=14, name='Zielladen-Standard', limit=ScheduledLimit(selected='soc', amount=1000, soc_limit=100, soc_scheduled=100), time='11:50')}), instant_charging=InstantCharging(current=17, limit=Limit(selected='none', amount=1000, soc=50)))) 2024-08-27 15:38:43,643 - {control.data:266} - {INFO:MainThread} - ev0 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='Standard-Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=True, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,644 - {control.data:266} - {INFO:MainThread} - ev1 EvData(set=Set(soc_error_counter=0), charge_template=1, ev_template=1, name='Corsa', tag_id=['0003411712', '0007501485'], get=Get(soc=72, soc_timestamp=1724765717.317447, force_soc_update=False, range=272, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,645 - {control.data:266} - {INFO:MainThread} - ev2 EvData(set=Set(soc_error_counter=0), charge_template=2, ev_template=2, name='BMW 225xe', tag_id=['0006721162', '0011214001'], get=Get(soc=68, soc_timestamp=1724765685.227685, force_soc_update=False, range=18.0, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,646 - {control.data:266} - {INFO:MainThread} - ev3 EvData(set=Set(soc_error_counter=0), charge_template=0, ev_template=0, name='neues Fahrzeug', tag_id=[], get=Get(soc=None, soc_timestamp=None, force_soc_update=False, range=None, fault_state=0, fault_str='Kein Fehler.')) 2024-08-27 15:38:43,647 - {control.data:266} - {INFO:MainThread} - et0 EvTemplateData(name='Standard-Fahrzeug-Vorlage', max_current_multi_phases=16, max_phases=3, phase_switch_pause=2, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=False, control_pilot_interruption_duration=4, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=82000, efficiency=90, nominal_difference=1, keep_charge_active_duration=40) 2024-08-27 15:38:43,648 - {control.data:266} - {INFO:MainThread} - et1 EvTemplateData(name='Corsa', max_current_multi_phases=16, max_phases=3, phase_switch_pause=120, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=17000, min_current=6, max_current_single_phase=32, battery_capacity=46000, efficiency=92, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:43,650 - {control.data:266} - {INFO:MainThread} - et2 EvTemplateData(name='BMW 225xe', max_current_multi_phases=16, max_phases=1, phase_switch_pause=50, prevent_phase_switch=False, prevent_charge_stop=False, control_pilot_interruption=True, control_pilot_interruption_duration=7, average_consump=20000, min_current=6, max_current_single_phase=16, battery_capacity=6000, efficiency=100, nominal_difference=1, keep_charge_active_duration=60) 2024-08-27 15:38:43,651 - {control.data:245} - {INFO:MainThread} - general_data GeneralData(chargemode_config=ChargemodeConfig(instant_charging=InstantCharging(phases_to_use=3), phase_switch_delay=5, pv_charging=PvCharging(bat_power_reserve=0, bat_power_reserve_active=False, control_range=[-500, 500], feed_in_yield=15000, phase_switch_delay=7, phases_to_use=1, bat_power_discharge=0, bat_power_discharge_active=False, min_bat_soc=50, bat_mode='ev_mode', switch_off_delay=60, switch_off_threshold=300, switch_on_delay=6, switch_on_threshold=1400), retry_failed_phase_switches=True, scheduled_charging=ScheduledCharging(phases_to_use=0, phases_to_use_pv=0), time_charging=TimeCharging(phases_to_use=3), unbalanced_load_limit=20, unbalanced_load=True), control_interval=10, extern_display_mode='local', extern=False, external_buttons_hw=False, grid_protection_active=False, grid_protection_configured=True, grid_protection_random_stop=0, grid_protection_timestamp=None, http_api=False, mqtt_bridge=False, prices=Prices(bat=0.0003, cp=0, grid=0.0003, pv=0.00012), range_unit='km', ripple_control_receiver=RippleControlReceiver(get=RippleControlReceiverGet(fault_state=0, fault_str='Kein Fehler.', override_value=100), module={'name': 'openWB Dimm- & Control-Kit', 'type': 'dimm_kit', 'configuration': {'ip_address': '192.168.0.158', 'port': 8899, 'modbus_id': 1}}, override_reference=<OverrideReference.CHARGEPOINT: 'chargepoint'>)) 2024-08-27 15:38:43,652 - {control.data:246} - {INFO:MainThread} - general_data-display local 2024-08-27 15:38:43,653 - {control.data:247} - {INFO:MainThread} - graph_data GraphData(config=Config(duration=120)) 2024-08-27 15:38:43,654 - {control.data:248} - {INFO:MainThread} - optional_data OptionalData(et=Et(get=EtGet(fault_state=0, fault_str='Kein Fehler.', prices={})), int_display=InternalDisplay(active=False, on_if_plugged_in=True, pin_active=False, pin_code='0000', standby=60, theme=<modules.display_themes.cards.config.CardsDisplayTheme object at 0x6f089a30>), led=Led(active=False), rfid=Rfid(active=True)) 2024-08-27 15:38:43,655 - {control.data:266} - {INFO:MainThread} - pv2 PvData(config=Config(max_ac_out=0), get=Get(currents=[0.0, 0.0, 0.0], daily_exported=16285.0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026677.0, fault_state=0, fault_str='Kein Fehler.', power=-2737.2)) 2024-08-27 15:38:43,656 - {control.data:250} - {INFO:MainThread} - pv_all_data PvAllData(config=Config(configured=True), get=Get(daily_exported=16285.0, fault_str='Kein Fehler.', fault_state=0, monthly_exported=504820.0, yearly_exported=3309807.0, exported=32026677.0, power=-2737.2)) 2024-08-27 15:38:43,660 - {control.data:266} - {INFO:MainThread} - system {'update_in_progress': False, 'perform_update': False, 'backup_cloud': {'backup_before_update': True}, 'ip_address': '192.168.188.43', 'current_commit': '2024-08-27 12:16:39 +0200 [8a5a467c2]', 'current_branch': 'Release', 'current_branch_commit': '2024-08-27 12:33:48 +0200 [a069e0f37]', 'current_missing_commits': ['2024-08-27 12:33:48 +0200 [a069e0f37] - Merge pull request #1843 from openWB/master', '2024-06-04 08:52:24 +0200 [417a30647] - Merge pull request #1649 from openWB/master', '2024-03-19 06:56:08 +0100 [a6b648645] - Merge pull request #1490 from openWB/master', '2024-03-14 11:48:27 +0100 [1d1d842c5] - Merge pull request #1367 from openWB/master'], 'boot_done': True, 'datastore_version': 54, 'dataprotection_acknowledged': True, 'usage_terms_acknowledged': True, 'debug_level': 10, 'release_train': 'master', 'version': '2.1.5', 'lastlivevaluesJson': {'timestamp': 1724765913, 'time': '15:38:33', 'grid': 0.092, 'house-power': 0.331, 'charging-all': 2.49, 'pv-all': 2.729, 'cp3-power': 2.49, 'ev1-soc': 72, 'ev2-soc': 68}, 'installAssistantDone': True, 'module_update_completed': True} 2024-08-27 15:38:43,661 - {control.data:279} - {INFO:MainThread} - device0 {'name': 'Hichi', 'type': 'json', 'id': 0, 'configuration': {'url': 'http://192.168.188.23/cm?cmnd=status%2010'}} 2024-08-27 15:38:43,664 - {control.data:281} - {INFO:MainThread} - component0 {'name': 'Hichi', 'type': 'counter', 'id': 0, 'configuration': {'jq_power': '.StatusSNS.SM.W', 'jq_exported': '.StatusSNS.SM.WhExported', 'jq_imported': '.StatusSNS.SM.WhImported', 'jq_powers': ['.StatusSNS.SM.W1', '.StatusSNS.SM.W2', '.StatusSNS.SM.W3'], 'jq_currents': [None, None, None]}} 2024-08-27 15:38:43,665 - {control.data:279} - {INFO:MainThread} - device2 {'name': 'Kostal Piko', 'type': 'kostal_steca', 'id': 2, 'configuration': {'ip_address': '192.168.188.27'}} 2024-08-27 15:38:43,667 - {control.data:281} - {INFO:MainThread} - component2 {'name': 'Kostal Piko', 'type': 'inverter', 'id': 2, 'configuration': {'variant_steca': False}} 2024-08-27 15:38:43,668 - {control.data:253} - {INFO:MainThread} - 2024-08-27 15:38:43,670 - {control.algorithm.algorithm:25} - {INFO:MainThread} - # Algorithmus 2024-08-27 15:38:43,672 - {control.counter:390} - {DEBUG:MainThread} - LP3 Switch-Off-Threshold prüfen: 55.93W, Schwelle: 300W, freigegebener Ãœberschuss 0W, Einspeisegrenze 0W 2024-08-27 15:38:43,674 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:43,675 - {control.algorithm.algorithm:30} - {INFO:MainThread} - **Mindestrom setzen** 2024-08-27 15:38:43,677 - {control.algorithm.min_current:20} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:43,679 - {control.counter:179} - {DEBUG:MainThread} - Zähler 0: [45.370000000000005, 39.29, 39.68]A verbleibende Ströme, 28064.14W verbleibende Leistung 2024-08-27 15:38:43,680 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 6A 2024-08-27 15:38:43,682 - {control.algorithm.algorithm:32} - {INFO:MainThread} - **Sollstrom setzen** 2024-08-27 15:38:43,684 - {control.counter:238} - {DEBUG:MainThread} - Anpassen des Regelbereichs 0W 2024-08-27 15:38:43,686 - {control.counter:501} - {DEBUG:MainThread} - Zähler 0: Begrenzung der verbleibenden Leistung auf 1064.1399999999994W 2024-08-27 15:38:43,687 - {control.algorithm.algorithm:38} - {INFO:MainThread} - **PV-geführten Strom setzen** 2024-08-27 15:38:43,690 - {control.algorithm.filter_chargepoints:102} - {DEBUG:MainThread} - Geordnete Ladepunkte [3] 2024-08-27 15:38:43,691 - {control.algorithm.surplus_controlled:45} - {INFO:MainThread} - Mode-Tuple Chargemode.PV_CHARGING - Chargemode.PV_CHARGING - False, Zähler 0 2024-08-27 15:38:43,692 - {control.loadmanagement:76} - {DEBUG:MainThread} - Leistungsüberschreitung auf 1064.1399999999994W korrigieren: [10.0, 0.0, 0.0] 2024-08-27 15:38:43,693 - {control.algorithm.surplus_controlled:121} - {DEBUG:MainThread} - Ungenutzten Sollstrom aufschlagen ergibt 11.616695652173911A. 2024-08-27 15:38:43,695 - {control.counter:186} - {DEBUG:MainThread} - Zähler 0: [39.753304347826095, 39.29, 39.68]A verbleibende Ströme, -227.70000000000027W verbleibender Ãœberschuss 2024-08-27 15:38:43,696 - {control.algorithm.common:90} - {INFO:MainThread} - LP3: Stromstärke 11.616695652173911A 2024-08-27 15:38:43,698 - {control.process:23} - {INFO:MainThread} - # Ladung starten. 2024-08-27 15:38:43,705 - {control.process:109} - {INFO:MainThread} - LP3: set current 11.62 A, state CHARGING_ALLOWED 2024-08-27 15:38:43,707 - {modules.common.component_context:25} - {DEBUG:set current cp3} - Update Komponente ['Ladepunkt'] 2024-08-27 15:38:43,982 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/power, Payload 2500.07, vorherige Payload: 2490.21 2024-08-27 15:38:43,984 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/chargepoint/get/imported, Payload 2713912.11, vorherige Payload: 2713904.05 2024-08-27 15:38:43,988 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/home_consumption, Payload 293.05999999999966, vorherige Payload: 331.25000000000006 2024-08-27 15:38:43,990 - {helpermodules.changed_values_handler:126} - {DEBUG:MainThread} - Topic openWB/set/counter/set/imported_home_consumption, Payload 2741413.4980709245, vorherige Payload: 2741412.6065495466 2024-08-27 15:38:46,000 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:50,012 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=smarthome_handler, args=(), kwargs={}) 2024-08-27 15:38:50,015 - {schedule:660} - {DEBUG:MainThread} - Running job Job(interval=1, unit=minutes, do=handler10Sec, args=(), kwargs={})
Dass die Sollstromstärke nur geändert wird, wenn der Regelbereich verlassen wird, ist so nicht im Hilfetext erklärt und auch nicht so umgesetzt. Es wird nicht nachgeregelt, aber auf kleine Schwankungen wird trotzdem reagiert.
-
openWB
- Site Admin
- Beiträge: 8499
- Registriert: So Okt 07, 2018 1:50 pm
- Has thanked: 1 time
- Been thanked: 27 times
Re: Rückmeldungen 2.1.5 Release
Das klingt eher nach Defekt am BMW. Rein technisch ist das ein PWM Signal, das wird üblicherweise vom Fahrzeug generell mehrmals pro Sekunde ausgewertet.Dahinter steckt das praktische Problem, dass der Onboard-Charger von meinem BMW 225xe die vielen Sollstromänderungen der openWB nicht toleriert und nach ca. 2 Stunden Ladezeit auf Error geht.
Supportanfragen bitte NICHT per PN stellen.
Hardwareprobleme bitte über die Funktion Debug Daten senden mitteilen oder per Mail an support@openwb.de
Hardwareprobleme bitte über die Funktion Debug Daten senden mitteilen oder per Mail an support@openwb.de
-
Gero
- Beiträge: 3417
- Registriert: Sa Feb 20, 2021 9:55 am
- Has thanked: 4 times
- Been thanked: 59 times
Re: Rückmeldungen 2.1.5 Release
Ich hab' den Fehler gefunden - es ist mein verstorbenes nodeRED zur Berechnung des Leistungsaufnahme des Heizstabs: https://forum.openwb.de/viewtopic.php?p=115332#p115332
Das smarthome hat weiterhin mit den 2,9kW weitergerechnet, obwohl der Heizstab aus war. Am EVU-Zähler waren dann natürlich diese 2,9kW zu viel, was den Hausverbrauch auf 0 korrigiert hatte. Da bin ich ein bisschen zu schnell mit meiner Meldung hier gewesen. Ich kann den Fehler aber nachstellen und ein Log bereitstellen, falls gewünscht.
Das smarthome hat weiterhin mit den 2,9kW weitergerechnet, obwohl der Heizstab aus war. Am EVU-Zähler waren dann natürlich diese 2,9kW zu viel, was den Hausverbrauch auf 0 korrigiert hatte. Da bin ich ein bisschen zu schnell mit meiner Meldung hier gewesen. Ich kann den Fehler aber nachstellen und ein Log bereitstellen, falls gewünscht.
openWB-series2, openWB-Buchse, E3/DC S10pro+19.5kWh, 30kWp Ost-Süd, Model 3 und Ion
Re: Rückmeldungen 2.1.5 Release
Bei jedem einstellbaren SoC-Wert noch einstellbar zu machen, was passiert, wenn dieser SoC nicht abrufbar ist, führt zu sehr ins Detail.Gero hat geschrieben: ↑Di Aug 27, 2024 5:35 pm Gerade hat mein Auto angefangen zu laden obwohl nicht mehr genügend Sonne da ist. Das SoC-Modul ist schuld. Irgendwas hat Tesla wohl wieder geändert, auf jeden Fall konnte der SoC nicht ermittelt werden und wird als Null angezeigt. Null ist kleiner als der eingestellte Mindest-SoC also fängt das Laden an.
Wir hatten hier ja schon mal die Diskussion, ob das Verhalten beim Zielladen bei nicht erfolgreichem SoC-auslesen nicht doch besser stattfinden sollte. Da war ich der Meinung, ja auf jeden Fall, denn besser das Auto ist zu voll als zu leer. (Die openWB hat nicht geladen, das fragliche Auto war am Morgen zu leer)
Beim Mindest-SoC wird nun also geladen obwohl das Erreichen des Ziel-SoCs nicht feststellbar ist und somit das Auto komplett voll geladen wird.
Nun denke ich, dass man doch einen Fehlerwert-SoC definieren müsste, auf den die jeweilige Laderlogiken - vielleich sogar einstellbar - reagieren. Beim Zielladen würde ich laden wollen, beim Mindest-SoC eher nicht. Aber es gibt ja auch ein SoC-Ladeziel bei Sofortladen, im PV-laden und im Zeitladen.
Vielleicht könnte der Punkt auf irgendeine ToDo-Liste, das ist ja wegen der vielen Stellen nun ein größerer Brocken, wenn man das implementiert. Und wenn man es einstellbar macht, braucht‘s das auch noch.
So ist es für alle Stellen, die den SoC verwenden, gleich umgesetzt. Wenn 3x kein SoC verfügbar ist, wird geladen.